Mophie powerstation go AC - User Manual

SAFETY PRECAUTIONS
DANGER-CAUTION Read and understand all safety information
before using this product. Failure to follow these instructions may
result in electrical shock, explosion, re which may result in serious
injuries, death or property damage.
• When used correctly, lithium- ion rechargeable batteries provide a
safe and dependable source of portable power. However, if they are
misused or abused, this may result in leakage, burns, re or explosion,
causing personal injury or damage to other devices.
• Misusing or incorrectly connecting your powerstation go AC may
cause electric shock to users and damage equipment.
• Do not operate in explosive atmospheres such as in the presence of
ammable liquids, gases or dust.
• Remove jump start clamps from vehicle battery after jump starting vehicle.
• Keep your powerstation go AC dry and away from moisture and
corrosive materials. The powerstation go AC should not be used near
water or wet areas such as bathtubs, showers, bathrooms, sinks,
swimming pools or basements.
• Do not expose your powerstation go AC to moisture, water, rain, or snow.
• Keep your powerstation go AC away from heat sources, including
open ames, radiators, stoves, ovens, and any other devices that
product heat.
• The lithium-ion rechargeable battery used in this charging
device may present a risk of re or chemical burn if mistreated. Do not
expose to re or excessive temperature. Do not expose to heat above
212°F (100°C) or incinerate.
• In the unlikely event of leakage or explosion use sand or a chemical
re extinguisher.
• Your powerstation go AC may become warm under extended high
power operation. Do not cover, wrap, or otherwise restrict the
powerstation go AC during operation.
• Do not disassemble your powerstation go AC. There are no user-
serviceable parts inside. Incorrect reassembly may result in shock
or re hazard.
• Do not drop or subject to strong impacts. Do not operate your
powerstation go AC if it has received a sharp blow, or has otherwise
been damaged in any way.
• Do not puncture, crush or subject to mechanical shock.
• Only charge your powerstation go AC by the specied method with
the specied charging adapter provided with the unit.
• Do not use any non-mophie-branded accessories with the
powerstation go AC. Doing so may cause electric shock to users and
damage equipment.
• The powerstation go AC, along with its accessories, are not toys and
should be kept away from children.
• Make sure the jumper cables are fully plugged into the jump start
output before trying to jumpstart your vehicle.
• Do not touch red (positive) and black (negative) jumper clamps
together at any point.
• Do not insert any foreign object into the ports or openings of your
powerstation go AC.
• Do not clean your powerstation go AC with harsh chemicals, soaps or
detergents. Just wipe the case with a soft cloth.
• Make sure the powerstation go AC’s charging ports do not become
contaminated with lint or other debris. Use a canned-air type of
product periodically to ensure that the port openings are clear.
• Batteries should be recycled or disposed of as per state and
local guidelines.
• Storage: -4°F – 158°F (-20°C – 70°C), Discharge: 14°F – 122°F
(-10°C – 50°C), Charge: 32°F – 113°F (0°C – 45°C)
OPERATING INSTRUCTIONS
Charging Your powerstation go AC
To charge your powerstation go AC, use the provided Wall Charging
Adapter, and plug the DC jack into the charging put. Next, connect the
wall charging adapter into a wall outlet. The powerstation go AC will
automatically begin charging. When the powerstation go AC is fully
charged, all ve battery indicator bars will be solid white and the digital
screen will indicate 100% charged. (This could take up to 9 hours).
While charging, the digital screen will illustrate the charge percentage
of the powerstation go AC. When fully charged, disconnect the cable.
NOTE:
The powerstation go AC is designed to charge between 32°F-113°F
(0-45° C). A "TEMP" indicator will be illustrated on the digital display if
the powerstation go AC is attempted to be charged outside of this
temperature range.
JUMP STARTING YOUR VEHICLE WITH
THE POWERSTATION GO AC
1. Plug the jumper cables into the jump start output on the
powerstation go AC.
2. Attach the jumper cable clamps to the vehicle battery.
- Red clamp on positive terminal (+)
- Black clamp on negative terminal (-)
CHARGING AN ELECTRONIC DEVICE USING
5V/2.4A USB OUTPUT PORT
1. Connect the USB-C tip of the supplied USB-C cable into the
USB-C input of your electronic device and connect the Standard
USB end of the supplied USB-C cable into either one of the
powerstation go AC USB 5V/2.4A Output ports.
2. Turn on the USB charging by pressing the
USB Power ON/OFF Button on the powerstation go AC.
SPECIFICATIONS
Battery Cells: Contains a battery with 3x Li-Polymer 5000mAh
Battery Pack Energy: 55500 mWh
Jump Start: 12V/600Amps
Input: 14V/0.85A
USB Output: 2x USB 5V/2.4A
Dimensions: 3.82 x 7.17 x 1.5 inches
Weight: 1.66 lbs
Operating Temperature (During Charging) 32°F - 113°F (0°C - 45°C)
Operating Temperature 14°F - 122°F (-10°C - 50°C)
COMPLIANCE WITH FCC REGULATION
This device complies with part 15 of the FCC Rules and RSS-Gen of IC
Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: To comply with the limits of the Class B digital device,
pursuant to Part 15 of the FCC Rules, this device must be used with
certied peripherals and shielded cables. All peripherals must be
shielded and grounded. Operation with non-certied peripherals or
non-shielded cables may result in interference to radio or reception.
LIMITED WARRANTY
At mophie, we are dedicated to making the best quality products. To
back this up, this product is warranted for 90 days. For full details
regarding warranty terms, exclusions and limitations, please visit:
mophie.com/warranty. This warranty does not aect any statutory
rights that you may be entitled to. Keep a copy of your purchase receipt
as proof of purchase. Be sure to register your product at mophie.com.
MOPHIE SMART CHARGE TECHNOLOGY
Your powerstation go AC contains the mophie SMART CHARGE
TECHNOLOGY to achieve higher compatibility for charging standard 5V
USB electronic devices. The mophie SMART CHARGE TECHNOLOGY will
allow the powerstation go AC to communicate with your electronic
device and provide the fastest and safest charge for that device.
COMPATIBILITY
Standard 5V USB electronic devices including: Mobile phones, Tablets,
PSP, NDS, MP3, MP4, MP5, Bluetooth, GPS, Cameras, and more.
USING YOUR POWERSTATION GO AC FLOODLIGHT
The oodlight can be turned on and o by simply pressing and
releasing the oodlight ON/OFF button. The rst press will turn on the
oodlight. Second press will turn on the red emergency light. Third
press will turn on SOS ashing red light. The oodlight will
automatically turn o after 2 hours of inactivity.
JUMP START TROUBLESHOOTING TIPS
3. Press the “Jump Start” button and wait for solid green light.
4. Start your vehicle.
5. Disconnect the jumper cable clamps from the car battery.
powerstation
®
go AC
OPERATING INSTRUCTIONS
powerstation go AC
Thank you for choosing mophie!
Powerful and loaded with features including a new, easy to use digital
display, the powerstation go AC can be used to safely jump start your
vehicle or provide portable power for your AC appliances. The
powerstation go AC can charge your laptop, phone, tablet and other
electronic devices anywhere! The powerstation go AC also includes a
convenient oodlight and emergency light. Compact, versatile and
simple to use, the powerstation go AC and all accessories t neatly in its
carrying pouch and is perfect to store in your home or vehicle for every
day use or an emergency need.
TABLE OF CONTENTS
Safety Precautions
Included Items
Operating Instructions
Troubleshooting Guide
Specications
Warranty and Contact Information

Summary

Safety Precautions

General Safety Warnings

Crucial warnings about electrical shock, explosion, fire, injury, death, or property damage.

Battery and Environmental Safety

Precautions for battery handling, environmental hazards like moisture, heat, and explosive atmospheres.

Operational Safety Guidelines

Instructions on removing clamps, device warmth, and emergency fire extinguisher use.

Included Items

Powerstation Go AC Components

Overview of the powerstation go AC unit and its included accessories, including ports and buttons.

Operating Instructions

Charging the Powerstation Go AC

Step-by-step guide on how to charge the device using the provided wall adapter and its expected charging time.

Jump Starting Your Vehicle

Detailed instructions for using the powerstation go AC to jump start a vehicle, including safety checks.

Charging a Laptop via AC Outlet

Procedure for powering laptops or other electronic devices using the AC output port, noting wattage limitations.

Charging Via USB Output Port

Instructions for charging electronic devices using the 5V/2.4A USB output ports, including cable compatibility.

Using the Floodlight

Guide on operating the integrated floodlight and emergency light functions, including SOS mode.

Troubleshooting Tips

Jump Start Troubleshooting

Common issues and solutions when attempting to jump start a vehicle with the powerstation go AC.

Laptop Charging Troubleshooting

Solutions for problems encountered while charging laptops or other devices via the AC output port.

Specifications and Compliance

Device Specifications

Technical details including battery capacity, jump start output, dimensions, weight, and operating temperatures.

FCC Regulatory Compliance

Information regarding FCC rules, device compliance, and measures to correct radio interference.

Limited Warranty and Support

Product Warranty Information

Details on the product's warranty period, terms, exclusions, and how to register the product.

Customer Service Contact

Contact information for customer support, including telephone numbers and website.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The mophie powerstation go AC is a versatile portable power solution designed for jump-starting vehicles, charging electronic devices, and providing illumination. It combines multiple functionalities into a compact and easy-to-use device, making it suitable for everyday use and emergency situations.

Function Description:

The primary function of the powerstation go AC is to safely jump-start vehicles. It is equipped with jumper cables and a dedicated jump start output. The device features a digital screen that displays the vehicle battery voltage when the clamps are attached, and a "Jump Start" button that indicates the status of the jump-start process with green or red lights. Safety checks are integrated into the jump-start function to prevent incorrect connections and ensure safe operation.

Beyond jump-starting, the powerstation go AC serves as a portable power source for various electronic devices. It includes an AC outlet, two USB 5V/2.4A output ports, and is compatible with USB-C charging. This allows users to charge laptops (rated 65 watts or less), phones, tablets, and other USB-powered devices. The device incorporates mophie's SMART CHARGE TECHNOLOGY to optimize charging speed and safety for connected USB devices.

Additionally, the powerstation go AC features a convenient floodlight and an emergency light. The floodlight can be turned on with a single press of its ON/OFF button. Subsequent presses activate a red emergency light and an SOS flashing red light, providing versatile lighting options for different scenarios.

Important Technical Specifications:

• Battery Cells: Contains a battery with 3x Li-Polymer 5000mAh cells.
• Battery Pack Energy: 55500 mWh.
• Jump Start: 12V/600Amps.
• Input: 14V/0.85A (for charging the powerstation go AC itself).
• USB Output: 2x USB 5V/2.4A.
• Dimensions: 3.82 x 7.17 x 1.5 inches.
• Weight: 1.66 lbs.
• Operating Temperature (During Charging): 32°F - 113°F (0°C - 45°C).
• Operating Temperature (Discharge/Storage): 14°F - 122°F (-10°C - 50°C) for discharge, and -4°F - 158°F (-20°C - 70°C) for storage.

Usage Features:

• Charging the powerstation go AC: The device is charged using the provided Wall Charging Adapter. Plug the DC jack into the charging input and the adapter into a wall outlet. The digital screen displays the charge percentage, and all five battery indicator bars will be solid white when fully charged (up to 9 hours). A "TEMP" indicator will appear if charging is attempted outside the safe temperature range (32°F-113°F).
• Jump Starting a Vehicle:
  1. Plug jumper cables into the jump start output.
  2. Attach red clamp to positive (+) terminal and black clamp to negative (-) terminal of the vehicle battery. The LCD will display vehicle battery voltage.
  3. Press the "Jump Start" button and wait for a solid green light (flashing green indicates safety checks).
  4. Start the vehicle. If it fails to start, wait 30 seconds and repeat steps 3 and 4.
  5. Disconnect clamps from the car battery.
  • Safety Features: The device prevents jump-starting if the USB or AC output modes are active. A "SAFETY CHECK FAIL" message appears if jumper cables are connected incorrectly, and the button flashes red. A "TEMP" indicator will be shown if jump-starting is attempted outside the safe operating temperature range.
• Charging a Laptop (AC Output Port):
  1. Connect the laptop's AC power plug (for devices rated 65 watts or less) into the AC output port.
  2. Press the AC Power ON/OFF Button and wait for a solid white light.
  • A flashing white light indicates safety checks. A flashing red light indicates the connected device exceeds 65 watts.
  • The AC charger automatically powers off after 30 minutes of inactivity.
  • AC output cannot be used while jump-starting the vehicle or charging the powerstation go AC itself.
• Charging Electronic Devices (USB Output Ports):
  1. Connect the USB-C tip of the supplied USB-C cable into the electronic device's USB-C input and the Standard USB end into one of the powerstation go AC's USB 5V/2.4A Output ports.
  2. Alternatively, use the charging cable provided with your electronic device, plugging its Standard USB end into one of the powerstation go AC's USB 5V/2.4A Output ports.
  3. Turn on USB charging by pressing the USB Power ON/OFF Button.
  • The USB charging feature automatically powers off after 30 minutes of inactivity.
  • USB output cannot be used while jump-starting the vehicle or charging the powerstation go AC itself.
• Floodlight and Emergency Light:
  • Press the Floodlight ON/OFF Button once for the floodlight.
  • Press a second time for the red emergency light.
  • Press a third time for the SOS flashing red light.
  • The floodlight automatically turns off after 2 hours of inactivity.
  • Caution: Do not look directly into the LED floodlight.

Maintenance Features:

• General Care: Keep the powerstation go AC dry and away from moisture, corrosive materials, heat sources (open flames, radiators, stoves, ovens), and water (bathtubs, showers, pools). Do not expose to fire, excessive temperature (above 212°F/100°C), rain, or snow.
• Cleaning: Do not use harsh chemicals, soaps, or detergents. Wipe the case with a soft cloth.
• Port Maintenance: Ensure charging ports are free of lint and debris. Use canned air periodically to keep openings clear.
• Storage: Store within the specified temperature range: -4°F – 158°F (-20°C – 70°C).
• Battery Disposal: Batteries should be recycled or disposed of according to state and local guidelines.
• Safety Precautions:
  • Do not disassemble the device; there are no user-serviceable parts.
  • Avoid dropping or subjecting to strong impacts. Do not operate if damaged.
  • Do not puncture, crush, or subject to mechanical shock.
  • Only charge with the specified charging adapter provided.
  • Do not use non-mophie-branded accessories.
  • Keep away from children.
  • Do not touch red (positive) and black (negative) jumper clamps together.
  • Do not insert foreign objects into ports or openings.
  • Do not cover, wrap, or restrict the powerstation go AC during operation, as it may become warm during high power use.
  • In case of leakage or explosion, use sand or a chemical fire extinguisher.

The powerstation go AC comes with a carrying pouch for convenient storage of the unit and its accessories, which include jumper cables, a wall charging adapter, and a USB-A to USB-C cable.

Mophie powerstation go AC Specifications