Components of your iron
⁄ Spray button
¤ Shot of steam button
‹ Variable steam button
› Filling hole with cap
fi Spray nozzle
fl Soleplate
‡ Temperature control dial with
indicator
· Water tank
(Illuminated on certain models)
‚ Life long anti-scale
(certain models only)
„ Temperature indicator light (red)
‰ Graduated filling beaker
 Self clean button
(certain models only)
Soleplate (certain models only)
Ê Turbo Tip
Powerful shot of steam gets into
the trickiest of places
Á Constant Steam
Remove all creases at a level you
control
Ë Press and Set
Removes moisture to set a
crease-free finish
Before first use
Note: The steam facility should only
be used on garments which are
suitable for ironing at the 2 and 3
dot settings.
When ironing with the steam facility
at the 2 dot setting, the steam
output should be set at the lower
end of the steam range (see
variable steam section).
Textiles and clothes are supposed to
carry ironing instructions. If they don’t
you should follow the temperature
guide on the previous page, but be
sure to test the temperature by
ironing the hem of the garment or
similar area first.
If you turn the control dial down from
a hot setting to a cooler setting, wait
until the iron temperature has
stabilised before you continue ironing.
Filling
1 Make sure that the iron is not
plugged in and then set the variable
s
team control ‹ to the ‘0’ position
before filling the iron with water.
2
Lift up the fill cap and fill the water
through the filling hole › into the
water tank ·, using the beaker
p
rovided A. After filling replace the
fill cap. In hard water areas the use
o
f distilled or demineralised water is
recommended.
WARNING: Never use battery
topping up fluid or water
containing any substances like
starch, or sugar, or defrosted
water from a refridgerator.
3 Always pour out the remaining
water after use.
WARNING: When filling your
iron with tap water always use
the beaker provided. Never fill
directly under the tap.
Tank capacity
Models 40701 - 400ml
Model 40707 and 40711 - 350ml
Temperature control
Plug in the iron and switch on. Set
the temperature control dial B to
the temperature required, but don’t
start ironing immediately.
If you wait a few minutes, the iron
will stabilise at the required setting.
Your Morphy Richards iron is fitted
with an indicator light „ which will
go on and off while you are ironing.
This is perfectly normal as it shows
that the iron is maintaining the heat
setting you have chosen.
It is always a good idea to begin
with cool fabrics and work up to
higher settings.
An iron heats up quicker than it
cools down so you’ll save time and
electricity.
Features of your iron
Temperature indicator light
The indicator light shows that the iron
i
s warming up. When the required
temperature is reached the light will
g
o out and will cycle on-off during
o
peration.
Dry ironing
Y
ou can use your iron as a dry iron
only. Make sure the variable steam
c
ontrol ‹ is set to the ‘0’ symbol.
A
ny temperature setting may be used
depending on the garment. The spray
feature may be used provided there
is water in the tank (see filling
section). You do not need to put any
water in the tank when dry ironing
only.
Spray
Press the spray button ⁄ and aim
the spray of water at stubborn
creases. You can do this whilst dry
ironing providing there is water in the
tank. When using the water spray it
may be necessary to push the button
a few times to get the spray pump
primed.
Variable steam
Fill the iron with water as described in
‘Filling’, page 4 and insert the plug
into the electrical socket.
The steam output can be varied from
low to high by turning the variable
steam control C. When using the
iron at 2-Dot, the steam output
should be adjusted to the low setting.
The steam facility should only be
used on garments which are suitable
for ironing at 2 and 3 dot setting.
Shot of steam
Press the shot of steam button ¤ to
obtain a burst of extra steam for
ironing out creases in heavy material
such as denim etc.
The shot of steam can be used whilst
dry ironing, providing there is water in
the tank, and the temperature control
is set within the steam range.
Do not use shot of steam at
temperatures below the steam range
shown on the control dial.
Note: For optimum steam quality, do
not operate the shot more than three
times in succession.
g
54
A
B
C
Lower steam
Higher steam
‹
¤⁄
›
fi
fl
‡
·
‚
„
‰
Electrical requirements
Check that the voltage on the rating
plate of your appliance corresponds
w
ith your house electricity supply
which must be A.C. (Alternating
c
urrent).
WARNING: This appliance must
be earthed.
UK only
I
f the socket outlets in your home
are not suitable for the plug
s
upplied with this appliance the
plug should be removed and the
appropriate one fitted.
WARNING: The plug removed
f
rom the mains lead, if severed,
m
ust be destroyed as a plug
with a bared flexible cord is
hazardous if engaged into a live
s
ocket outlet.
Where used, should the fuse in the
1
3 amp plug require changing a
13 amp BS1362 fuse must be fitted.
300
350
400
Â
Ë
Ê
Á
To Next Page
Loading...
