Morphy Richards IBCR1905

To Next Page

Illustration

Location of controls

1 Mains lead

2 Speaker grille

3 Time button

4 Sleep button

5 Function selector switch

6 Snooze button

7 Minute button

8 Hour button

9 Alarm button

10 Battery compartment

(located on the base)

11 FM wire aerial

12 PM indicator

13 Alarm on indicator

14 Dial scale and pointer

15 Band selector MW/FM

16 Tuning control

17 Volume control

Switching on and setting the clock time

Before any alarm functions can be used, you must set the clock to the correct

time.

1 Place the unit on a flat surface. Plug the mains plug (1) into the wall socket

and switch on the wall socket

2 The LED clock display (18) will flash.

3 Press and hold the TIME button (3) and simultaneously hold down the

HOUR button (8) or the MINUTE button (7). The LED clock display (18) will

fast forward the minutes and hour segments. Release the TIME button (3)

when your desired time is set.

4 The PM indicator (12) will illuminate to indicate 12.00 midday has been

reached.

Radio operation

FM wire aerial

To obtain the maximum FM reception fully extend the wire FM aerial (11) (which is

located at the rear of the unit) and alter the direction of the wire for best results.

The aerial for the MW waveband is located inside the unit. To obtain the

maximum MW reception rotate the clock radio.

1 Slide the FUNCTION SELECTOR switch (5) to the ‘ON’ position.

2 Adjust the VOLUME control (17) to a suitable level.

3 Set the BAND SELECTOR switch (15) to either MW or FM as

desired.

4 Slowly adjust the TUNING control (16) to select your desired

station.

5 To switch off the radio, slide the FUNCTION SELECTOR

switch (5) to the ‘OFF’ position.

2 Band Alarm

Clock Radio

CR1905 OPERATING INSTRUCTIONS

Battery back-up facility

Your alarm clock radio is equipped with a battery back-up facility.

Your alarm clock radio will operate without a 9 volt battery fitted.

1 Remove the battery compartment cover (located underneath the unit)

by pressing the tab down and pulling the battery cover off.

2 Insert a battery size 9 volts PP3/6LR61. Ensure batteries are positioned

correctly. (Correct polarity is marked inside the battery compartment).

3 Replace the battery compartment cover.

Should a power interruption occur the clock will continue to run, however, time

keeping will not be accurate. The display will be extinguished to conserve battery

life, but the memory will retain details of the clock time and alarm settings.

If the optional battery is not installed in case of the AC power failure the display

will blink to indicate the power was interrupted. You will need to reset the clock and

alarm.

Battery back-up is designed to operate for a short period only.

If the unit is not to be used for a prolonged period, remove the battery to

avoid battery leakage.

In the interests of environmental safety : dispose of batteries safely.

Electrical requirements

Check that the voltage on the rating plate of your clock radio corresponds

with your house electricity supply which must be A.C. (Alternating current).

For clock radios with fitted plug.

If the socket outlets in your home are not suitable for the plug supplied

with this appliance the plug should be removed and the appropriate one

fitted.

IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED,

MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS

HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET.

Should the fuse in the 13 amp mains plug require changing a 3 amp BS1362

fuse must be fitted.

P. 2

P. 3 P. 4

Need help?

Do you have a question about the Morphy Richards IBCR1905 and is the answer not in the manual?

Summary

Electrical Requirements

For Clock Radios with Fitted Plug

Information regarding plug compatibility and fuse replacement for fitted plugs.

Battery Back-up Facility

Details on how the clock radio operates using a backup battery.

Setting Clock and Radio

Switching on and Setting the Clock Time

Guide to setting the correct time on the clock radio.

Radio Operation

Instructions for tuning FM and MW radio stations.

Alarm Functions

Alarm Operation

Steps to set the alarm time and select alarm type (buzzer/radio).

Wake up to the Radio Alarm

Instructions for setting a radio alarm, including tuning and volume.

Wake up to the Alarm Buzzer

How to set the alarm to use the built-in buzzer.

Alarm Control and Sleep Function

To Stop the Alarm Tone

How to stop the alarm, either temporarily or permanently.

Snooze Function

Details on how to use the snooze feature for temporary alarm interruption.

To Set the Sleep Function

Guide to setting the radio to turn off automatically after a set time.

Product Information

Maintenance

Care instructions, cleaning, and environmental advice for the clock radio.

Technical Specification

Key technical details including power supply and radio frequencies.

Guarantee

Information about the product guarantee and warranty claims.

Warning Labels

Explanation of safety symbols and warnings for electrical hazards.