Motor Guard MAGNA-STITCHER MS-1-KIT User Manual

MAGNA-STITCHER
TM
INSTRUCTIONS
Plastic Repair Kit
Model MS-1-KIT
Patent Pendin
g
*
WARNING: Read and understand all instructions before attempting to operate tool.
Failure to follow instructions may result in electric shock, fire and/or serious
personal injury.
Review and follow all instructions for your electric stud welder.
If you do not have the original instructions for your stud welder, contact the
manufacturer for a replacement copy.
IMPORTANT SAFETY INSTRUCTIONS
* 8
To reduce the risk of serious
injury and/or property damage,
observe all warnings and
instructions while operating the
tool. Keep work area clean and well
lit. Maintain tool in top condition and
obtain service from manufacturer if
tool malfunctions. Use only
accessories and replacement parts
that are provided by the
manufacturer.
Stud welder must be connected
to a properly grounded outlet
installed in accordance with all local
codes and ordinances. Never
remove the grounding prong or
modify the plug in any way. Do not
use adapter plugs. Consult an
electrician if you are in any doubt as
to whether the plug is properly
grounded. Avoid bodily contact with
grounded surfaces.
= !
A
Always wear proper personal
protection when operating welder.
A full face shield per ANSI Z87.1-
2003 standard is required at all times
to protect face and eyes against
injury from flying parts. Adequate
gloves and clothing are required to
reduce the risk of burns. Allow parts
to cool before handling.
Do not operate tool in explosive
atmospheres, such as in the
presence of flammable liquids,
gases or dust. Welders create
sparks which may ignite dust or
fumes. Use in well ventilated areas
only. Welders generate heat which
can ignite surrounding materials
causing fires.
SAVE THESE INSTRUCTIONS
IF YOU HAVE ANY QUESTIONS ABOUT THE OPERATION OF PRODUCT CALL TOLL FREE
800-227-2822
8:00 am to 5:00 pm - Pacific Time - Monday through Friday

Motor Guard MAGNA-STITCHER MS-1-KIT Specifications

General

Brand	Motor Guard
Model	MAGNA-STITCHER MS-1-KIT
Category	Welding Accessories
Language	English

Summary

Important Safety Instructions

General Safety Precautions

Reduce risk of injury/damage by observing warnings and instructions. Keep work area clean, maintain tool.

Personal Protective Equipment

Always wear proper personal protection, including face shield and gloves, to prevent injury.

Electrical Safety

Ensure stud welder is connected to a properly grounded outlet and avoid contact with grounded surfaces.

Hazardous Atmospheres

Avoid operating in explosive atmospheres; sparks can ignite flammable materials. Use in well-ventilated areas.

Application and Installation

Product Application

The Magna Stitcher turns a stud welder into a plastic repair tool for various automotive parts.

Tool Installation

Install the Magna Stitcher on the stud welder by seating it firmly against the insulator.

Work Area Preparation

Prepare the repair area by removing all dirt, oil, and dust for optimal results.

General Repair Procedure

Insert stake, heat briefly to melt plastic, allow to sink halfway, twist to lock, and let cool.

Specific Repair Techniques

Repairing Flat Areas

Use an S-Shaped Magna-Stake for flat areas, inserting and spacing stakes 1/2 to 3/4 inch apart.

Repairing Tabs and Thin Sections

Use an M-Shaped Magna-Stake for tabs and thin sections, adding stakes as needed for strength.

Repairing Inside Corners

Use a V-Shaped Magna-Stake for inside corners, inserting and spacing stakes 1/2 to 3/4 inch apart.

Repairing Outside Corners

Use a W-Shaped Magna-Stake for outside corners, inserting and spacing stakes 1/2 to 3/4 inch apart.

Parts and Warranty Information

Replacement Stakes

Details on S, M, V, and W-shaped Magna-Stakes for different repair applications.

Replacement Parts List

Identifies the Magna-Stitcher Repair Tool (MS-1) and Replacement Thumb Screw (M1003).

Limited Warranty

Covers defects in workmanship/material for one year; excludes normal wear and misuse.