EasyManua.ls Logo

Motorola MG160 Series - User Manual

Motorola MG160 Series
8 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MG160 Series
KEM-ML37104-01B
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general
safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To control
your exposure and ensure compliance with the general population/
uncontrolled environment exposure limits, always adhere to the
following procedure:
Transmit no more than 50% of the time.
To receive calls, release the PTT button.
To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting
(in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines:
United States Federal Communications Commission, Code of
Federal Regulations; 47CFR part 2 sub-part J.
American National Standards Institute (ANSI)/Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992.
Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.
International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998.
Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 KHz to 300 GHz, 1999.
Australian Communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
To ensure optimal radio performance and make sure human
exposure to radio frequency electromagnetic energy is within the
guidelines set forth in the above standards, always adhere to the
following procedures.
P
ortable Radio Operation and EME Exposure
A
ntenna Care
U
se only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could
d
amage the radio and may violate FCC regulations.
D
o NOT hold the antenna when the radio is IN USE. Holding the
antenna affects its effective range.
B
ody-Worn Operation
T
o maintain compliances with FCC/Health Canada RF exposure
guidelines if you wear a radio on your body when transmitting
a
lways place the radio in a Motorola-supplied or approved clip
holder, holster, case or body harness for this product. Use of
n
on-Motorola-approved accessories may exceed FCC/Health
C
anada RF exposure guidelines.
If you do not use one of the Motorola-supplied or approved
b
ody-worn accessories and are not using the radio held in the
n
ormal use position, ensure the radio and its antenna are at least 1
inch (2.5 cm) from your body when transmitting.
D
ata Operation
I
f applicable, when using any data feature of the radio with or
without an accessory cable, position the radio and its antenna at
l
east one inch (2.5 cm) from the body.
Approved Accessories
F
or a list of approved Motorola accessories, visit our Web site at
w
ww.motorolasolutions.com/talkabout.
Electromagnetic Interference/Compatibility
N
ote: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic compatibility.
T
his device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
F
acilities
To avoid electromagnetic interference and/or compatibility conflicts,
t
urn off your radio in any facility where posted notices instruct you
to do so. Hospitals or health care facilities may be using equipment
that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard an
aircraft. Any use of a radio must be in accordance with applicable
regulations per airline crew instructions.
Medical Devices Pacemakers
The Advanced Medical Technology Association recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations
are consistent with the independent research by and
recommendations of the U.S. Food and Drug Administration.
People with pacemakers should:
ALWAYS keep the radio more than 6 inches (15 cm) from their
pacemaker when the radio is turned ON.
Not carry the radio in the breast pocket.
Use the ear opposite the pacemaker to minimize the potential for
interference.
Turn the radio OFF immediately if there is any reason to suspect
that interference is taking place.
Medical Devices Hearing Aids
Some digital wireless radios may interfere with some hearing aids.
In the event of such interference, you may want to consult your
hearing aid manufacturer to discuss alternatives.
Medical Devices Other
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately shielded
from RF energy. Your physician may be able to assist you in
obtaining this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the
area where you drive, and always obey them. If you do use your
radio while driving, please:
Give full attention to driving and to the road.
Use hands-free operation, if available.
Pull off the road and park before making or answering a call if
driving conditions so require.
The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your ability
to safely participate in such activities. Always use technology safely.
F
or More Information
For further information, you may call Motorola at 1-800-638-5119
(
U.S.), or e-mail us at support@giantintl.com or visit us on the
I
nternet at www.motorolasolutions.com/talkabout.
D
o not place a portable radio in the area over an air bag or in the air
bag deployment area. Air bags inflate with great force. If a portable
r
adio is placed in the air bag deployment area and the air bag
inflates, the radio may be propelled with great force and cause
s
erious injury to occupants of the vehicle.
P
otentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially
e
xplosive atmosphere. Only radio types that are especially qualified
s
hould be used in such areas as Intrinsically Safe. Do not remove,
i
nstall or charge batteries in such areas. Sparks in a potentially
e
xplosive atmosphere can cause an explosion or fire resulting in
bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to
a
bove include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
c
hemicals or particles (such as grain, dust or metal powders) and
a
ny other area where you would normally be advised to turn off your
vehicle engine. Areas with potentially explosive atmospheres are
o
ftenbut not alwaysposted.
Blasting Caps and Areas
T
o avoid possible interference with blasting operations, turn off your
r
adio when you are near electrical blasting caps, in a blasting area,
or in areas posted Turn off two-way radios. Obey all signs and
i
nstructions.
Operational Cautions
A
ntennas
D
o not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn
c
an result.
Batteries
All batteries can cause property damage and/or bodily injury such as
b
urns if a conductive materiallike jewelry, keys or beaded chains
touch exposed terminals. The conductive material may complete an
e
lectrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
pocket, purse or other container with metal objects.
Exercise care when removing batteries. Do not use sharp or
c
onductive tools to remove the batteries.
FCC Licensing Information
Your Motorola radio operates on General Mobile Radio Service
(GMRS) frequencies and is subject to the Rules and Regulations of
the Federal Communications Commission (FCC). The FCC requires
that all operators using GMRS frequencies obtain a radio license
before operating their equipment. To obtain the FCC forms, please
visit the FCCs Web site at wireless.fcc.gov/uls/index.htm?job=home
to source form 605 and 159, which includes all the instructions you
will need.
If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
Changes or modifications not expressly approved by Motorola may
void the users authority granted by the FCC to operate this radio and
should not be made. To comply with FCC requirements, transmitter
adjustments should be made only by or under the supervision of a
person certified as technically qualified to perform transmitter
maintenance and repairs in the private land mobile and fixed
services as certified by an organization representative of the user of
those services. Replacement of any transmitter component (crystal,
semiconductor, etc.) not authorized by the FCC equipment
authorization for this radio could violate FCC rules.
You can find the label with the FCC ID in the battery compartment.
Note: Use of this radio outside the country where it was intended to
be distributed is subject to government regulations and may be
prohibited.
®
Two-Way Radio
User’s Guide
T
urning Your Radio On and Off
1. To turn on, press and hold until a channel number appears
a
nd the radio beeps.
2. To turn off, press and hold until the display goes blank.
S
etting the Volume
1
. Press the to increase or to decrease the volume. The
volume level flashes and V displays.
D
o not hold the radio close to your ear. If the volume is set to an
u
ncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
c
hannel.
1
. To talk, press and hold .
2. When you are finished talking, release .
F
or maximum clarity, hold the radio two to three inches away from
your mouth and speak directly into the microphone. Do not cover the
m
icrophone while talking.
Note:
This radio does not have Interference Eliminator Codes. To
c
ommunicate with radios that use Interference Eliminator Codes, the
Interference Eliminator Code must be set to 0.
T
alk Range
Your radio is designed to maximize performance and improve
t
ransmission range. Do not use the radios closer than five feet apart.
Monitor Button
U
se this feature to see if there is anyone on the channel you have
selected.
1
. Press and hold to check for the channel activity.
2. When you finish listening, release the button.
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio
s
tops transmitting if you press for 60 continuous seconds.
Menu Options
Selecting the Channel
1. With the radio on, press . The current channel flashes.
2. Press or and select a channel.
3. Press or to confirm your selection.
Channels and Frequencies
Transmitting Call Tones
To transmit your call tone to other radios set to the same channel as
your radio, press .
Note: To receive the call tone, radios that use Interference
Eliminator Codes must be set to 0.
P
TT
Numbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
Scan
P
TT
Numbers for Channel,
Call Tone
Volume
L
ow Battery Icon
Keypad Lock
T
ransmitting
Receiving
Scan
PTT
Numbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
S
can
P
TT
Numbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
S
can
PTT
Numbers for Channel,
Call Tone
Volume
Low Battery Icon
K
eypad Lock
Transmitti ng
Receiving
Scan
PTT
Numbers for Channel,
Call Tone
Volume
L
ow Battery Icon
Keypad Lock
T
ransmitting
Receiving
Scan
P
TT
Numbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
R
eceiving
S
can
PTT
Numbers for Channel,
C
all Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
Scan
P
TT
Numbers for Channel,
Call Tone
Volume
L
ow Battery Icon
Keypad Lock
T
ransmitting
R
eceiving
Scan
GIANT TELECOM LIMITED
Customer : GI
Model Number : MG160
Description: LCD display graphics
& Line drawing (front view)
Version : R01
Date : Mar 04, 2013
PTT
Numbers for Channel,
Call Tone
1:1 Scale
1:1 Scale
1
4mm
1
1mm
2:1 Scale
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
Scan
PTT
N
umbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
Scan
P
TT
N
umbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
S
can
P
TT
Numbers for Channel,
Call Tone
Volume
L
ow Battery Icon
Keypad Lock
T
ransmitting
Receiving
S
can
PTT
N
umbers for Channel,
Call Tone
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
Scan
Display Screen Guide
Continued on back
MG160 Series
Control Buttons
GIANT TELECOM LIMITED
C
ustomer : GI
Model Number : MG160
Description: LCD display graphics
&
Line drawing (front view)
Version : R01
Date : Mar 04, 2013
PTT
Numbers for Channel,
C
all Tone
1:1 Scale
1:1 Scale
14mm
11m m
2:1 Scale
Volume
Low Battery Icon
Keypad Lock
Transmitti ng
Receiving
Scan
Getting Started
Installing the Batteries
Each radio uses 3 AAA alkaline batteries.
Installing the Three AAA Alkaline Batteries
1. Turn the radio off.
2. With the bottom of the radio facing you, use a small screwdriver,
pen, or similar tool as illustrated below to remove the cover.
3. Insert the three AAA alkaline batteries with + and - polarity as
shown inside.
4. Reposition the battery cover and press down to secure.
Removing the Battery Cover
Push pen inwards with small amount of pressure and raise slightly upwards
Removing the Three AAA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, remove the cover.
3. Gently remove each alkaline battery by easing each battery out
individually.
4. Reposition the battery cover and press down to secure.
Notes:
Exercise care when removing the batteries. Do not use sharp or
conductive tools to remove the batteries.
Remove the alkaline batteries before storing your radio for
extended periods of time. Batteries corrode over time and may
cause permanent damage to your radio.
Attaching and Removing the Belt Clip
Hook the belt clip into the notch at the top of the radio and slide it
down until it clicks into place.
To Remove
Squeeze the release latch together and slide the clip up and away
from the radio.
For a fax:
Contact the
Fax-0n-Demand
system
For mail service:
Call the FCC Forms
Hotline
If you have
questions about
the FCC License:
Call the FCC
1-202-418-0177 1-800-418-FORM
(3676)
1-888-CALL-FCC
(225-5322)
Channel Frequency Description Channel Frequency Description
1 462.5625 MHz GMRS/FRS 12 467.6625 MHz FRS
2 462.5875 MHz GMRS/FRS 13 467.6875 MHz FRS
3 462.6125 MHz GMRS/FRS 14 467.7125 MHz FRS
4 462.6375 MHz GMRS/FRS 15 462.5500 MHz GMRS
5 462.6625 MHz GMRS/FRS 16 462.5750 MHz GMRS
6 462.6875 MHz GMRS/FRS 17 462.6000 MHz GMRS
7 462.7125 MHz GMRS/FRS 18 462.6250 MHz GMRS
8 467.5625 MHz FRS 19 462.6500 MHz GMRS
9 467.5875 MHz FRS 20 462.6750 MHz GMRS
10 467.6125 MHz FRS 21 462.7000 MHz GMRS
11 467.6375 MHz FRS 22 462.7250 MHz GMRS
PTT
N
umbers for Channel,
Call Tone
V
olume
L
ow Battery Icon
Keypad Lock
T
ransmitting
R
eceiving
S
can
GIANT TELECOM LIMITED
Customer : GI
Model Number : MG160
Description: How to open the battery door
Version : R02
Date : Jun 14, 2013
Radio scale 1:1
Best Fitting for User Guide
Radio scale 1:1
Best Fitting for User Guide
Option A
Option B
Question and Answer IconNeed help?

Do you have a question about the Motorola MG160 Series and is the answer not in the manual?

Summary

Safety and General Information

Important Information on Safe and Efficient Operation

Read this information before using your radio for safe and efficient operation.

Transmit and Receive Procedure

Procedure to control exposure and ensure compliance with RF limits.

Exposure to Radio Frequency Energy

Details Motorola radio compliance with RF energy exposure standards and guidelines.

Portable Radio Operation and EME Exposure

Body-Worn Operation

Maintaining RF exposure compliance when wearing the radio on the body.

Medical Devices - Pacemakers

Recommendations for maintaining separation between radio and pacemakers.

Safety and General Use While Driving

Guidelines for safe radio use while driving, emphasizing attention to the road.

Potentially Explosive Atmospheres

Blasting Caps and Areas

Operational Cautions

FCC Licensing Information

Getting Started

Installing the Batteries

Step-by-step guide to installing three AAA alkaline batteries into the radio.

Talking and Listening

Menu Options

Selecting the Channel

Steps to select a new channel on the radio using menu options.

Special Features

Low Battery Alert

Notification when the battery is low, indicated by a flashing icon and chirping.

Scan

How to use the scan feature to search for transmissions or active channels.

Keypad Lock

How to lock and unlock the keypad to prevent accidental setting changes.

Warranty

Exclusions

Overview

The Motorola Talkabout MG160 Series is a two-way radio designed for safe and efficient operation, offering communication capabilities for various uses. It functions as both a transmitter and a receiver, operating within specific radio frequency energy exposure standards and guidelines set by regulatory bodies such as the United States Federal Communications Commission (FCC), American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE), International Commission on Non-Ionizing Radiation Protection (ICNIRP), Ministry of Health (Canada), Australian Communications Authority, and ANATEL.

Function Description:

The primary function of the MG160 Series radio is two-way communication. Users can transmit by pressing the Push to Talk (PTT) button and receive calls by releasing it. To ensure compliance with general population/uncontrolled environment exposure limits, it is crucial to transmit no more than 50% of the time, as the radio generates measurable RF energy exposure only during transmission. The radio operates on 22 channels, utilizing frequencies within the GMRS/FRS bands, ranging from 462.5500 MHz to 467.7125 MHz. It supports both GMRS (General Mobile Radio Service) and FRS (Family Radio Service) frequencies, allowing for versatile communication.

Important Technical Specifications:

The radio is powered by three AAA alkaline batteries. It features a display screen guide with indicators for channel number, call tone, low battery, keypad lock, transmitting (TX), receiving (RX), and scan mode. The microphone and speaker are integrated into the device. Volume control is managed through dedicated up (+) and down (-) buttons. The device also includes a scan/monitor button and a power/menu button. The model number is KEM-ML37104-01B, and it belongs to the MG160 Series.

Usage Features:

  • Turning On/Off: The radio is turned on by pressing and holding the Menu button until a channel number appears and a beep is heard. To turn it off, the Menu button is held until the display goes blank.
  • Volume Control: Volume can be adjusted using the + and - buttons. The volume level flashes, and "V" is displayed during adjustment. Users are advised not to hold the radio close to their ear if the volume is set to an uncomfortable level to prevent hearing damage.
  • Talking and Listening: To communicate, all radios in a group must be set to the same channel. To talk, the PTT button is pressed and held. To listen, the PTT button is released. For optimal clarity, the radio should be held two to three inches away from the mouth, and the user should speak directly into the microphone, ensuring it is not covered.
  • Interference Eliminator Codes: This radio does not have Interference Eliminator Codes. To communicate with radios that use these codes, the Interference Eliminator Code on those radios must be set to 0.
  • Talk Range: The radio is designed to maximize performance and transmission range. It is recommended not to use radios closer than five feet apart.
  • Monitor Button: The MON button allows users to check for activity on the selected channel. Pressing and holding MON checks for channel activity, and releasing it stops monitoring.
  • Push to Talk (PTT) Timeout Timer: To prevent accidental transmissions and conserve battery life, the radio automatically stops transmitting if the PTT button is pressed for 60 continuous seconds.
  • Channel Selection: With the radio on, the Menu button is pressed, causing the current channel to flash. Channels can then be selected using the + or - buttons, and the selection is confirmed by pressing PTT or Menu.
  • Transmitting Call Tones: A call tone can be transmitted to other radios on the same channel by pressing the call tone button. Radios receiving the call tone must have their Interference Eliminator Codes set to 0.
  • Low Battery Alert: When the battery is low, the low battery icon flashes, and the radio chirps periodically.
  • Talk Confirmation Tone: The radio transmits a unique tone upon finishing transmission, signaling "Roger" or "Over" to other users.
  • Scan Feature: The scan function allows users to search all 22 channels for transmissions from unknown parties, to find group members who have accidentally changed channels, or to locate unused channels. To start a scan, the MON button is briefly pressed; the scan icon appears, and the radio scrolls through channels. When activity is detected, it stops scrolling, allowing the user to hear the transmission. To respond, the PTT button must be pressed within five seconds of the transmission ending. The radio resumes scanning five seconds after activity ceases. To stop scanning, the MON button is briefly pressed again.
  • Keypad Lock: To prevent accidental changes to radio settings, the keypad can be locked by pressing and holding the lock button until the lock icon appears. In lock mode, users can still turn the radio on/off, receive, transmit, send call tones, and monitor channels, but all other functions are locked. To unlock, the lock button is pressed and held until the lock icon disappears.

Maintenance Features:

  • Battery Installation/Removal: The radio uses three AAA alkaline batteries. To install, the battery cover is removed using a small screwdriver or similar tool. The batteries are inserted with correct polarity (+ and -), and the cover is repositioned and pressed to secure. To remove batteries, the radio is turned off, the battery cover is removed, and each battery is gently eased out. The battery cover is then repositioned and pressed to secure.
  • Belt Clip: The belt clip is attached by sliding it into the notch at the top of the radio until it clicks into place. To remove, the release latch is squeezed, and the clip is slid away from the radio.
  • General Care: Users are advised to exercise care when removing batteries and not to use sharp or conductive tools. Removing batteries for extended periods is recommended to prevent corrosion and damage.
  • RF Energy Exposure: To ensure optimal radio performance and compliance with safety guidelines, users must always adhere to the specified procedures for transmitting and receiving, and avoid transmitting more than 50% of the time.
  • Electromagnetic Interference/Compatibility: The radio is designed to comply with FCC rules regarding electromagnetic compatibility. It is important to note that this device may not cause harmful interference and must accept any interference received.
  • Portable Radio Operation and EME Exposure: The radio should be placed at least one inch (2.5 cm) from the body when transmitting. When worn on the body, it should be placed in a Motorola-supplied or approved holder, holster, case, or body harness.
  • Medical Devices: If using a personal medical device, consult a physician or the device manufacturer to determine if it is adequately shielded from RF energy.
  • Driving Safety: When driving, users should give full attention to driving and the road, use hands-free operation if available, and pull off the road and park before making or answering a call if driving conditions require.
  • Blasting Caps and Areas: Users must turn off the radio in areas where blasting operations are in progress or in "blasting areas" to avoid potential interference with blasting caps.
  • Potentially Explosive Atmospheres: Users must turn off the radio before entering any area with a potentially explosive atmosphere, such as areas where fuel is stored, chemical transfer facilities, or areas containing chemicals or particles (grain, dust, or metal powders).
  • Batteries: Batteries can cause property damage and/or bodily injury if handled improperly. Users should exercise care when handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects.
  • Cleaning: Do not use sharp or conductive tools to remove batteries.

The Motorola Talkabout MG160 Series is a reliable and user-friendly two-way radio, designed with safety and performance in mind for effective communication in various environments.

Motorola MG160 Series Specifications

General IconGeneral
BrandMotorola
ModelMG160 Series
CategoryTwo-Way Radio
LanguageEnglish

Related product manuals