Mountain Mods Modular Removable Motherboard Tray - User Manual

Mountain Mods – Modular Removable Motherboard Tray – Instructions / Assembly
The Mountain Mod Modular/Removable motherboard tray comes flat packed. Each individual item is wrapped
tightly in a special non-adhesive static cling plastic wrap. The wrap protects the finish from scratching,
scuffing, fingerprints and movement during transit. It is important to TAKE CARE when removing the wrap.
It is recommended to find the edge of the wrap and unroll it or grab a pair of scissors, create a pocket by lifting
up an area of plastic and cut the wrap. Make sure if you use sharp instruments to not scratch into the parts.
It is not recommended to rip the plastic as this may cause bending of parts from the pressure placed upon them.
PARTS LIST (items that come with the motherboard tray)
In the diagram on the next page items are listed that are included with the Mountain Mods Modular/Removable
motherboard tray.
A) Motherboard Tray - this is what you mount your motherboard to.
B) Motherboard Back Panel – this is the exterior panel. It fastens to the rear of the case from the outside.
C) I/O Panel – this is what is known as the I/O (input/output) panel. I/O ports and PCI devices attach here.
D) Security flange – This attaches to a corner of the motherboard tray to eliminate movement once in place.
NOTE the comments below about the security flange as an option and which cases do not include it.
E) 10 pack of standoffs/3mm computer screws – The standoffs mount to the tray. The motherboard sits on
the standoffs with appropriate mounting holes aligned. Then the 3mm screws tighten into the female end of the
standoffs and hold the motherboard to the tray.
F)) 25 pack of 6-32 computer screws – These 6-32 computer screws are used for the assembly of back panel to
I/O Panel and I/O – back panel assembly to the motherboard tray itself. These are also included to fasten the
PCI plates into the tray as well as other expansion devices.
G) 6 x PCI cover plates – These are included with the tray to cover any empty PCI slots that are not being
used.

Summary

Parts List

Motherboard Tray Component

The primary component onto which the motherboard is mounted.

Motherboard Back Panel Component

The exterior panel that fastens to the rear of the case.

I;O Panel Component

The panel for I/O ports and PCI devices attachment.

Security Flange Component

Attaches to the tray corner to eliminate movement.

Standoffs and 3 mm Screws

Mount to the tray; motherboard sits on standoffs, secured by 3mm screws.

6-32 Computer Screws

Used for assembly of back panel, I/O panel, PCI plates, and expansion devices.

PCI Cover Plates

Plates to cover any empty PCI slots.

Assembly Instructions

Assemble Back Panel and I;O Panel

Fasten the Motherboard Back Panel (B) to the I/O Panel (C) using seven 6-32 screws.

Attach I;O-Back Panel Assembly to Motherboard Tray

Connect the assembled Back Panel/I/O Panel to the Motherboard Tray (A) using four 6-32 screws.

Secure I;O Panel from Underside

Fasten the I/O panel to the motherboard tray from the underside using three 6-32 screws.

Install Security Flange

Attach the security flange using two tapered screws for ATX or reverse ATX.

Mount Motherboard and Expansion Cards

Attach motherboard with standoffs and expansion cards with 6-32 screws; use PCI cover plates.

Mountain Mods Modular Removable Motherboard Tray Specifications

General

Material	Aluminum
Dimensions	Varies by model
Weight	Varies by model
Removable	Yes
Compatibility	ATX, Micro-ATX, Mini-ITX
Form Factor	ATX, Micro-ATX, EATX
Color	Black
Type	Modular Removable Tray