EasyManua.ls Logo

MQ Multiquip MAYCO C-30HDNI - User Manual

MQ Multiquip MAYCO C-30HDNI
137 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PARTS AND OPERATION MANUAL
Concrete Pump
Model C-30HDNI
(FUEL INJECTION)
Revision #0 (05/15/03)
Go to Discount-Equipment.com to order your parts

Table of Contents

Questions and Answers

  • V
    Victor ParkerAug 5, 2025
    Why MQ Multiquip Water Pump engine will not start?
    • C
      Crystal RobertsAug 5, 2025
      If your MQ Multiquip Water Pump's engine won't start or the start is delayed, and the engine can be turned over, several factors could be at play. First, ensure the speed control lever is in the "START" position. Other potential causes include a defective fuel pump (replace it), a clogged fuel filter (replace the fuel filter and clean the tank), or a faulty fuel supply line (replace or repair it). Also, check if the compression is too low (inspect the piston, cylinder, and valves, adjusting or repairing as needed per the engine repair manual), the oil pressure is too low (check engine oil pressure), the low starting temperature limit has been exceeded (comply with cold starting instructions and use proper oil viscosity), or the battery is defective (charge or replace it).
  • J
    James ArmstrongAug 16, 2025
    What to do if MQ Multiquip Water Pump engine stops by itself?
    • C
      Christine AndersonAug 16, 2025
      If your MQ Multiquip Water Pump engine stops by itself during normal operation, it could be due to several reasons. The fuel tank might be empty, so add fuel. Alternatively, the fuel filter could be blocked, requiring replacement. A defective fuel pump could also be the culprit, necessitating replacement. Lastly, the mechanical oil pressure shutdown sensor might be stopping the engine due to low oil; in this case, add oil and replace the low oil shutdown sensor if necessary.
  • K
    Karen BrandtAug 26, 2025
    What to do if MQ Multiquip MAYCO C-30HDNI engine fires then stops?
    • W
      Wendy ZimmermanAug 26, 2025
      If your MQ Multiquip Water Pump engine fires but stops as soon as the starter is switched off, check the following: Ensure the throttle lever is in the RUN position. A blocked fuel filter can cause this issue, so replace it. Also, check the entire fuel system for any blockages in the fuel supply. Lastly, an electrical problem at the fuel solenoid could be the cause; repair it using #7 wire.

Summary

Introduction and Specifications

Heres How to Get Help

Guidance on obtaining assistance for the concrete pump operation and maintenance.

Pump Specifications

Key technical details of the Mayco C-30HDNI concrete pump.

Engine Specifications

Technical details of the Nissan A15 industrial engine.

Pump Dimensions

Physical dimensions and measurements of the concrete pump.

General Information

Overview of operating principles and suggestions for the concrete pump.

Safety and Operation

Safety Message Alert Symbols

Explanation of danger, warning, and caution symbols used in the manual.

Rules For Safe Operation

Guidelines and precautions for safe operation of the concrete pump.

Important Hand Signals

Standard hand signals used during concrete pumping operations.

Operating Information

Suggestions and procedures for operating the concrete pump during various conditions.

Maintenance and Troubleshooting

Inspection and Start-Up

Procedures for pre-operation inspection and initial start-up of the pump.

Maintenance (Pump)

Recommended maintenance tasks and procedures for the pump.

Engine Troubleshooting

Common engine problems and their solutions for the Mayco pump.

Malfunction Indicator Codes

Diagnostic error codes for engine malfunctions and their meanings.

Systems, Components, and Diagrams

Pump Components

Identification and illustration of major pump components.

Control Box Components

Description of functions for each component on the pump's control box.

Engine Components

Identification of basic engine components for the Nissan A15 engine.

Wiring Diagrams

Electrical diagrams for EFI system and trailer lights.

Concrete Mix Information

Guidelines and specifications for concrete mixes suitable for pumping.

Suggested Spare Parts

List of recommended spare parts for the Mayco C-30HDNI pump.

Parts Illustrations

Nameplate and Decals

Location and identification of nameplates and safety decals on the pump.

Pump Mechanical Assemblies

Illustrated breakdown of major pump mechanical assemblies.

Engine Assemblies

Illustrated breakdown of major engine component assemblies.

Control and Electrical Assemblies

Illustrated breakdown of control box, battery, and electrical systems.

Trailer Assemblies

Illustrated breakdown of trailer frame and axle components.

Warranty

Mayco Pump Warranty

Details of the manufacturer's warranty terms and conditions for Mayco pumps.

MQ Multiquip MAYCO C-30HDNI Specifications

General IconGeneral
EngineHonda GX160
Pump TypeCentrifugal
Inlet Size2 in
Outlet Size2 in
Horsepower5.5 HP
Engine ModelGX160
Suction Lift25 ft
Max Output304 gpm (1151 lpm)