MSF 16th Edition - T-CLOCS: Pre-Ride Inspection Checklist; T - Tires & Wheels; C - Controls; L - Lights

EMERGENCY INFORMATION
Rider's Name __________________________________________________________Blood Type ________________ Allergies/Medical Conditions _______________________________________________________________________ Doctor's Name/Phone _____________________________________________________________________________ Cycle Insurer Name/Phone _________________________________________________________________________
Contact this person if rider is injured
Name ____________________________________________ Home Phone ___________________________________ Work Phone ______________________________________ Cell Phone _____________________________________
T-TIRES & WHEELS Tires Condition Tread depth, wear, weathering, evenly seated, bulges, embedded objects.
Front Rear
Air Pressure Check when cold, adjust to load.
Front Rear
Wheels Spokes Bent, broken, missing, tension, check at top of wheel: “ring” = OK — “thud” = loose spoke
Front Rear
Cast Cracks, dents.
Front Rear
Rims Out of round/true = 5mm. Spin wheel, index against stationary pointer.
Front Rear
Bearings Grab top and bottom of tire and ex: No freeplay (click) between hub and axle, no growl when spinning.
Front Rear
Seals Cracked, cut or torn, excessive grease on outside, reddish-brown around outside.
Front Rear
Brakes Function Each brake alone keeps bike from rolling.
Front Rear
C-CONTROLS Levers and Pedal
Condition Broken, bent, cracked, mounts tight, ball ends on handlebar levers, proper adjustment.
Pivots Lubricated.
Cables Condition Fraying, kinks, lubrication: ends and interior.
Routing No interference or pulling at steering head, suspension, no sharp angles, wire supports in place.
Hoses Condition Cuts, cracks, leaks, bulges, chang, deterioration.
Routing No interference or pulling at steering head, suspension, no sharp angles, hose supports in place.
Throttle Operation Moves freely, snaps closed, no revving when handlebars are turned. L-LIGHTS Battery Condition Terminals; clean and tight, electrolyte level, held down securely.
Vent Tube Not kinked, routed properly, not plugged.
Headlamp Condition Cracks, reector, mounting and adjustment system.
Aim Height and right/left.
Operation Hi beam/low beam operation.
Tail lamp/ brake lamp
Condition Cracks, clean and tight.
Operation Activates upon front brake/rear brake application.
Turn signals Operation Flashes correctly.
Front left Front right
Rear left Rear right
Mirrors Condition Cracks, clean, tight mounts and swivel joints.
Aim Adjust when seated on bike.
Lenses & Reflectors
Condition Cracked, broken, securely mounted, excessive condensation.
Wiring Condition Fraying, chang, insulation.
Routing Pinched, no interference or pulling at steering head or suspension, wire looms and ties in place, connectors tight, clean.
O-OIL Levels Engine Oil Check warm on center stand on level ground, dipstick, sight glass.
Hypoid Gear Oil,
Shaft Drive
Transmission, rear drive, shaft.
Hydraulic Fluid Brakes, clutch, reservoir or sight glass.
Coolant Reservoir and/or coolant recovery tank — check only when cool.
Fuel Tank or gauge.
Leaks Engine Oil Gaskets, housings, seals.
Hypoid Gear Oil,
Shaft Drive
Gaskets, seals, breathers.
Hydraulic Fluid Hoses, master cylinders, calipers.
Coolant Radiator, hoses, tanks, ttings, pipes.
Fuel Lines, fuel valve, carbs.
T-CLOCS ITEM WHAT TO CHECK WHAT TO LOOK FOR
CHECK-OFF
You can tear this page out and keep it with you when you ride.
T-CLOCS ITEM WHAT TO CHECK WHAT TO LOOK FOR
CHECK-OFF
T-CLOCS: Pre-Ride Inspection Checklist
C-CHASSIS Frame Condition Cracks at gussets, accessory mounts, look for paint lifting.
Steering-Head Bearings No detent or tight spots through full travel, raise front wheel, check for play by pulling/pushing forks.
Swingarm Bushings/
Bearings
Raise rear wheel, check for play by pushing/pulling swingarm.
Suspension Front Forks Smooth travel, equal air pressure/damping, anti-dive settings.
Left Right
Rear Shock(s) Smooth travel, equal pre-load/air pressure/damping settings, linkage moves freely and is lubricated.
Left Right
Chain or Belt Tension Check at tightest point.
Lubrication Side plates when hot. Note: do not lubricate belts.
Sprockets Teeth not hooked, securely mounted
Fasteners Threaded Tight, missing bolts, nuts.
Clips Broken, missing.
Cotter Pins Broken, missing.
S-STANDS Center stand Condition Cracks, bent.
Retention Springs in place, tension to hold position.
Side stand Condition Cracks, bent (safety cut-out switch or pad equipped).
Retention Springs in place, tension to hold position.