2-12
Hardware Setup
▍
MS-7549
Seral ATA Connector: SATA1~6
Ths connector s a hgh-speed Seral ATA nterface port. Each connector can connect
to one Seral ATA devce.
F
l
o
p
p
y
D
M
S
I
F
l
o
p
p
y
D
M
S
I
K
d
k
l
k
d
k
f
k
k
k
f
d
k
k
l
d
d
f
k
k
k
s
d
d
f
d
d
f
a
s
d
k
a
d
f
-
d
d
f
d
d
a
d
d
f
d
f
d
d
d
d
d
f
a
d
f
a
d
k
j
a
s
j
d
k
d
f
d
f
a
s
d
d
d
f
f
a
s
d
f
d
d
d
d
d
d
d
f
d
a
s
f
d
a
s
a
s
d
f
a
s
d
a
s
d
a
s
d
d
d
d
d
d
d
f
a
s
a
s
d
f
s
d
f
f
s
d
f
a
d
f
f
f
a
s
d
f
f
f
d
f
F
l
o
p
p
y
D
M
S
I
K
d
k
l
k
d
k
f
k
k
k
f
d
k
k
l
d
d
f
k
k
k
s
d
d
f
d
d
f
a
s
d
k
a
d
f
-
d
d
f
d
d
a
d
d
f
d
f
d
d
d
d
d
f
a
d
f
a
d
k
j
a
s
j
d
k
d
f
d
f
a
s
d
d
d
f
f
a
s
d
f
d
d
d
d
d
d
d
f
d
a
s
f
d
a
s
a
s
d
f
a
s
d
a
s
d
a
s
d
d
d
d
d
d
d
f
a
s
a
s
d
f
s
d
f
f
s
d
f
a
d
f
f
f
a
s
d
f
f
f
d
f
Important
Please do not fold the Seral ATA cable nto 90-degree angle. Otherwse, data loss may
occur durng transmsson.
Fan Power Connectors: CPUFAN1, SYSFAN1
The fan power connectors support system coolng fan wth +12V. When connectng the
wre to the connectors, always note that the red wre s the postve and should be con-
nected to the +12V; the black wre s Ground and should be connected to GND. If the
manboard has a System Hardware Montor chpset on-board, you must use a specally
desgned fan wth speed sensor to take advantage of the CPU fan control.
1
.
G
r
o
u
n
d
2
.
+
1
2
V
3
.
S
e
n
s
o
r
4
.
C
o
n
t
r
o
l
CPUFAN1 SYSFAN1
Important
Please refer to the recommended CPU fans at processor’s ocal webste or consult
the vendors for proper CPU coolng fan.
CPUFAN1 supports fan control. You can nstall
Dual Core Center utlty that wll auto-
matcally control the CPU fan speed accordng to the actual CPU temperature.
Fan cooler set wth 3 or 4 pns power connector are both avalable for CPUFAN1.
SYSFAN1 support fan control, too. You may select how percentage of speed for the
SYSFAN1 n BIOS.
•
•
•
•