EasyManua.ls Logo

MTD Gold 31AS2T5E504 - User Manual

MTD Gold 31AS2T5E504
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
P. O. Box 1386, 97 KENT AVENUE, KITCHENER, ON N2G 4J1
Printed In USA
OPERATOR’S MANUAL
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
769-100 40
07. 0 8 .14
Single-Stage Snow Thrower

Table of Contents

Questions and Answers

  • A
    awangAug 3, 2025
    What to do if my MTD Gold 31AS2T5E504 Snow Blower won't throw snow?
    • V
      vbrownAug 3, 2025
      If your MTD Gold Snow Blower isn't discharging snow, several factors could be at play. First, the chute assembly might be clogged; to resolve this, stop the engine, disconnect the spark plug wire, and then clean the chute and the inside of the auger housing using a clean-out tool or a stick. Second, a foreign object might be lodged in the auger; in this case, stop the engine immediately, disconnect the spark plug wire, and remove the object. Third, the auger control cable may be out of adjustment; adjust the auger control cable. Lastly, the auger belt could be loose or damaged, requiring replacement.
  • Q
    qcamachoAug 10, 2025
    Why is my MTD Gold Snow Blower losing power?
    • J
      Justin SandersAug 10, 2025
      If your MTD Gold Snow Blower is experiencing a loss of power, there are a couple of potential causes. First, the spark plug wire might be loose; to fix this, firmly connect the spark plug wire. Second, the vent in the gas cap could be plugged; if so, clear the vent.
  • T
    Tiffany GreenAug 15, 2025
    Why do the augers keep spinning on my MTD Gold 31AS2T5E504 Snow Blower?
    • J
      John HayesAug 16, 2025
      If the augers on your MTD Gold Snow Blower continue to rotate, it's likely that the auger control cable is out of adjustment. To resolve this, adjust the auger control cable as described in the Maintenance & Adjustments section.
  • C
    Charles MossAug 22, 2025
    Why won't my MTD Gold 31AS2T5E504 move on its own?
    • J
      Judith LawsonAug 22, 2025
      If your MTD Gold Snow Blower fails to self-propel, there could be a couple of reasons. First, the auger control cable might be out of adjustment; you can adjust it as shown in the Maintenance & Adjustments section. Second, the auger drive belt might be loose or damaged, requiring replacement.
  • O
    oandersonAug 27, 2025
    How to fix excessive vibration in my MTD Gold 31AS2T5E504?
    • S
      Stephen DanielsAug 27, 2025
      Excessive vibration in your MTD Gold Snow Blower can stem from loose parts or a damaged auger. Immediately stop the engine and disconnect the spark plug wire. Check for any damage and tighten all bolts and nuts. Repair as needed. If the vibration persists, take the snow thrower to an authorized service dealer.

Summary

Important Safe Operation Practices

Safety Warnings and Dangers

Highlights critical safety warnings, including Proposition 65 and general dangers.

Pre-Operation Training

Pre-Operation Preparation

Safe Handling of Gasoline

Gasoline Handling Precautions

Detailed instructions on safe fuel handling, storage, and refueling procedures.

General Operation Safety Guidelines

Essential safety guidelines for operating the snow thrower to prevent injury and damage.

Maintenance & Storage

Clearing a Clogged Discharge Chute

Steps to safely clear a clogged discharge chute using a tool, not hands.

Safety Device and Component Checks

Engine Governor and Modification Warning

Safety Symbols

Symbol Descriptions

Operator Responsibility Warning

Assembly & Set-Up

Positioning the Upper Handle

Installing the Discharge Chute

Installing the Recoil Starter Handle

Recoil Starter Handle Installation

Operation

Engaging the Auger

Engaging the Drive

Clearing a Clogged Discharge Chute

Maintenance & Adjustments

Shave Plate Adjustment

Procedures for checking and adjusting the shave plate for proper contact with the surface.

Control Cable Adjustment

Service

Replacing Belt

Detailed instructions for removing and installing the drive belt.

Service

Replacing Auger Paddles

Steps for replacing worn auger paddles, emphasizing using OEM parts.

Replacing Shave Plate

Instructions for replacing or reversing the shave plate due to wear.

Troubleshooting

Loss of Power

Lists potential causes and remedies for loss of engine power.

Excessive Vibration

Identifies causes and solutions for excessive machine vibration.

Snow Thrower Fails to Self-Propel

Addresses issues with the machine not moving forward and their solutions.

Augers Continue to Rotate

Explains why augers might continue rotating and how to fix it.

Unit Fails to Discharge Snow

Provides remedies for the unit not throwing snow effectively.

THREE YEAR LIMITED WARRANTY

Warranty Coverage and Limitations

Details what the limited warranty covers, exclusions, and duration.

Obtaining Warranty Service

MTD Gold 31AS2T5E504 Specifications

General IconGeneral
Engine Displacement (cc)208
Auger MaterialSteel
Number of Auger Blades2
Chute ControlManual
Engine Type4-cycle OHV
Start TypeElectric start
Forward SpeedsNot Applicable
Reverse SpeedsNot Applicable