Mugen Seiki MSX3 User Manual

1/1 0 NITRO TOURING CAR
~
SHAFT DRIVE 4WD
!&m~~.
INSTRUCTION MANUAL
.Technical Data •
• Length·· .. · .. · .. · ................................. 388mm
.Width··
........................................... ·198mm
.Height··
.. · .......... ·· .... ·· .... ····· ........ · .... 103mm
.Wheel Base" ................................... 259mm
.Tread(F/R)··
.. · .. · .......... ·· .. · .. ··· 172mm/172mm
.Wheel Diameter(F/R)" ........... ~ 65mm x 26mm
.Gear Ratio ........................................ 7.6 : 1
.Weight·· ........ · .... ·····
.. ···· .. · .. · .... · .. ·· .. · .. 1700g
......... ®
O!w~
MSX3
*.jI*~~
Semi-Assembled
Kit
.:t'.:; Hi, ~ J'~ alt:.5!: 0) t:bi:> 715; Ij: < f± ¥.A~~ J!9" Q': t 1:1""" 1)£9" 0
The contents are subject to change without notice.
~;j1t
.Iij]~~JOC;tiJJ.:",., -:" 0 • .7. 71 t-:':f,., 'j', 7')L-.7.51-51 -i"q(7) MV12 I /::;/}~tio
Wffl?77-, I7"7-()L-51-f;j" 0 .:",.,7 t- t-:'7174WD
o
.ii1i~~"'·"'·)L-=¥"\1p\:J~(7)T7 0
.1f 7')L- r) 1 ':J :".:z. *' - /-if.7.« /:" :3 /7" - 1>. 0 .:lE:gI;:t 1 wM )..;rt1f / I~- 0
.3t~l'~IJ1'1(7)~~\3mm 7")L-~ 7·v- t-:",.,-:" o .7)L- /\;'7"I) /7 0
.Feature •
• Semi-assembled chassis .
• Powerful
MV12 engine equipped. w/Slide carburetor and Pull-starter .
• Original muffer
and air filter .
•
Four wheel drive system wi Sh aft drive .
• Differential w/built-in FIR bevel gears .
•
Double wishbone suspension arms .
•
3mm AI. chassis .
•
Full- Bearing.
=;=274-0817 f-~~JiJG~m~mIIlJ1395iH-jg
~
l*~~t± 1w. ~N *~ tI
MUGEN SEIKI CO.,L TD.
MUG ENS ElK I 1395 TAKANE-CHO, FUNABASHI, CHIBA 274-0817, JAPAN
L--- __________ ---'® Phone:047-430-1663 Fax:047'-430-1665

Mugen Seiki MSX3 Specifications

General

Brand	Mugen Seiki
Model	MSX3
Category	Motorized Toy Car
Language	English

Summary

Product Specifications and Features

Technical Data

Key physical and mechanical specifications of the car.

Key Features

Highlights of the car's design and components.

Preparation and Tools

Required Items and Tools

Parts, tools, and items needed for assembly and engine starting.

Radio System Setup

Procedure to set servo neutral positions and check radio.

Assembly - Initial Steps

Unboxing and Disassembly

Unpacking the kit components and removing initial parts.

Mechanical Plate and Tank Removal

Removing specific parts to begin assembly.

Assembly - Servos and Receiver

Attaching Servos

Mounting the steering and throttle servos.

Attaching Receiver and Switch

Installing the radio receiver and switch.

Assembly - Mechanical and Fuel System

Attaching Mechanical Plate and Tank

Re-attaching the mechanical plate and fuel tank.

Attaching Fuel Pipe

Connecting the fuel lines to the engine.

Assembly - Linkages

Steering Linkage Attachment

Connecting the steering servo to the steering mechanism.

Throttle Linkage Attachment

Connecting the throttle servo to the engine.

Brake Linkage Attachment

Connecting the brake mechanism.

Assembly - Engine Control Linkage

Neutral Position Adjustment

Adjusting linkage for neutral throttle and brake positions.

Throttle High Adjustment

Adjusting linkage for full throttle opening.

Brake Adjustment

Adjusting linkage for brake operation.

Assembly - Dampers

Damper Oil Filling

Procedure for filling shock absorbers with oil.

Damper Exploded View

Diagram showing all parts of the shock absorber.

Assembly - Dampers and Air Filter

Attaching Dampers

Mounting the assembled shock absorbers onto the chassis.

Attaching Air-Filter

Installing the air filter onto the engine.

Assembly - Tires

Tire Assembly

Putting together the tires and wheels.

Tire Attachment

Mounting the assembled wheels onto the car.

Assembly - Body Mounts

Body Mount Attachment

Installing the body mounting posts.

Assembly - Bodywork

Body Cutting and Preparation

Cutting and preparing the car body for mounting.

Attaching Rear Wing

Mounting the rear wing to the body.

Mounting Body

Attaching the prepared body to the chassis.

Drivetrain - Differentials

Front/Rear Differential Components

Components of the front and rear differentials.

Front Differential Unit Assembly

Detailed assembly of the front differential.

Rear Differential Unit Assembly

Detailed assembly of the rear differential.

Drivetrain - Gearbox and Shafts

Spur Gear Mount Unit Assembly

Assembly of the spur gear mount.

Servo Saver Unit Assembly

Assembly of the servo saver mechanism.

Center Shaft Installation

Installation of the center shaft.

Suspension System Assembly

Front Suspension Arm Unit Assembly

Assembly of the front suspension arms.

Rear Suspension Arm Unit Assembly

Assembly of the rear suspension arms.

Suspension Arm Attachment

General suspension arm components and attachment.

Component Mounting

Radio Plate and Receiver Box Mounting

Mounting the radio receiver and related components.

Bumper and Body Mount Installation

Installing the front bumper and body mounts.

Engine, Tank, and Muffler Mounting

Mounting the engine, fuel tank, and muffler.

Engine and Damper Units

Damper Components and Assembly

Details on damper parts and how to assemble them.

Engine and Clutch Unit Assembly

Assembly of the engine and clutch components.

MV12 Engine Parts List

Carburetor Adjustment Procedures

Adjusting Engine Idling

Setting the idle speed of the engine.

Adjusting Main Needle

Adjusting the main needle for high-speed performance.

Adjusting Slow Needle

Adjusting the slow needle for low-speed performance.

Engine Starting Procedures

Radio System Activation

Powering on the transmitter and receiver.

Fueling the Engine

Adding fuel to the engine's fuel tank.

Engine Choking Procedure

Priming the engine using the choke.

Engine Operation and Shutdown

Engine Starting Methods

Various methods for starting the engine.

Handling an Over-Choked Engine

Procedure for dealing with a flooded engine.

Engine Stopping Procedure

How to safely shut down the engine.

Troubleshooting Guide

Parts List (Japanese)

Parts List (English)