To Next Page
А
АндрейOct 6, 2026
Здравствуйте. У нас такая проблема. Контроллер не загружается. При включении идет загрузка до 90 процентов и дальше ничего не происходит. В этом состоянии и остаётся. И не отображается ip адрес
Здравствуйте. У нас такая проблема. Контроллер не загружается. При включении идет загрузка до 90 процентов и дальше ничего не происходит. В этом состоянии и остаётся. И не отображается ip адрес
Ensures reliability by proper grounding and separation of high/low voltage wiring.
Using EMI filters for inverters and following installation guidelines to prevent interference.
Checking battery level and following inverter installation to avoid interference.
Emphasizes electrician installation, power disconnection, and compliance with electrical codes.
Details proper grounding, waterproof splices, and shield cable connections for low power devices.
Instructions on how to mount the Trio unit, including knockouts and hanging.
Provides diagrams for various connections like relays, power, internet, and devices.
Step-by-step guide for wiring a CO2 sensor, including port connections and wire colors.
Shows how to connect RTS sensors to T and COM ports, and the grounding strip.
Defining humidity sensors and water meters, including specific measurement parameters.
Details on wiring ammonia sensors, including port connections and resistor installation.
Requirements for connecting to TrioAir, including cable type and distance limits.
Steps to view and manage Wi-Fi, IP address, Support ID, and Munters ID.
Instructions for creating and managing accounts on trioair.net for farm management.
Procedure for pairing a Trio unit using its unique ID code (QR code) to an account.
Details input power, AC power, I/O specs, communication, and environmental ratings.
Explains the function of touch screen icons and the dashboard overview.
Explains mapping and defining devices for system control, starting with overview.
Steps to define fan relays or analog ports for on-off or variable speed control.
Defining stir fan parameters and operation modes, including on-off and cycle settings.
Defining day-specific minimum and maximum ventilation percentages for automatic adjustment.
Increasing or decreasing ventilation at extreme temperatures based on user-defined differentials.
How to define ammonia and CO2 sensors, including offset and enable mode.
Defining humidity sensors and water meters, including specific measurement parameters.
Steps to define on/off heaters, variable heaters, and cooling devices.
How to define a relay as a sprinkler, including KWh and operation modes.
Mapping relays to analog ports and setting up timers for device operation.
Configuring measuring fans and setting up feeder relays and sensors.
Defining the RPS sensor and calibrating static pressure for accurate readings.
Setting preferences, units, time/date, and room settings for the unit.
Defining herd data points and using a wizard for batch setup and historical data reset.
Defining expected animal weights and adjusting the animal count in the herd.
Setting target temperatures for growth days to create an automatic temperature adjustment curve.
Defining minimum/maximum ventilation, dynamic ventilation, and ventilation schemes.
Setting desired levels for humidity, CO2, and ammonia to trigger air treatment.
Procedures for resetting unit settings, backing up, and loading configurations.
Steps to download and install software updates for the Trio unit.
Steps to diagnose and resolve no internet connection issues.
Diagnosing and resolving problems with touch screen, inputs, and output components.
Table detailing device counts for various sensors and outputs for different versions.
Visual identification of container spare parts with corresponding ID numbers and descriptions.
Visual identification of door card components with corresponding ID numbers and descriptions.
Visual identification of main container components with corresponding ID numbers and descriptions.
Lists supported devices, required software version, and internet access methods.
Steps for installing the modem, SIM card, and antenna, including drilling if needed.
Steps to enable and configure the cellular modem via System > General Settings > Network.
Details the limited warranty for Munters products, coverage, and exclusions.
General| Brand | Munters |
|---|---|
| Model | Rotem Trio 20 |
| Category | Controller |
| Language | English |
