Murana WSG112 User Manual (English)

Questions and Answers:

L
Lisa SpencerJul 31, 2025
Why won't my Murana WSG112 engine start?
- J
  jeffreymcknightAug 1, 2025
  There are several reasons why your Murana Snow Blower engine might fail to start: * The fuel tank may be empty or the fuel may be stale. Fill the tank with clean, fresh gasoline, as fuel becomes stale after thirty days. * The fuel line could be blocked. Clean the fuel line. * The Choke/Run button may not be in the CHOKE position. Move the button to the CHOKE position. * The spark plug may be faulty. Clean, adjust the gap, or replace the spark plug. * The spark plug wire may be disconnected. Connect the spark plug wire. * The primer button may not be used properly. Refer to the engine manual.
C
Courtney OliverAug 6, 2025
What to do if my Murana WSG112 unit fails to discharge snow?
- P
  patrick91Aug 6, 2025
  If your Murana Snow Blower fails to discharge snow, here's what you should check: * The chute assembly may be clogged. Stop the engine and disconnect the spark plug wire. Clean the chute and inside of the auger housing with a clean-out tool or a stick. * The shear pins may be sheared. Replace the shear pins. * A foreign object may be lodged in the auger. Stop the engine immediately and disconnect the spark plug wire. Remove the object from the auger. * The auger control cable may need adjustment. Refer to the Making Adjustment Section. * The auger belt may be loose or damaged. Refer to a service centre or call 1 (877) 840-0840.
V
Valerie GrantAug 11, 2025
Why does my Murana Snow Blower engine run erratically?
- L
  Luke MccallAug 11, 2025
  An erratic running engine in your Murana Snow Blower can be caused by a few things: * The unit might be running on CHOKE. Move the CHOKE/RUN button to RUN. * There could be a blocked fuel line or stale fuel. Clean the fuel line and fill the tank with clean, fresh gasoline. * Water or dirt might be in the fuel system. Drain the fuel tank and carburetor, then refill with fresh fuel.
B
Brittany MendezAug 15, 2025
Why does my Murana Snow Blower have a loss of power?
- C
  christineharrisAug 15, 2025
  A loss of power in your Murana Snow Blower may be due to: * A loose spark plug wire. Connect and tighten the spark plug wire. * A plugged gas cap vent hole. Remove any ice and snow from the gas cap, ensuring the vent hole is clear.
A
Angie CraneAug 21, 2025
What to do if Murana WSG112 unit fails to propel itself?
- M
  Mackenzie PriceAug 21, 2025
  If your Murana Snow Blower isn't moving on its own, check these: * The drive control cable may need adjustment. Adjust the drive control cable. Refer to Making Adjustment Section. * The drive belt might be loose or damaged. Replace the drive belt. Refer to a service centre or call 1 (877) 840-0840.

Murana WSG112 Specifications

General

Brand	Murana
Model	WSG112
Category	Snow Blower
Language	English

Summary

IMPORTANT SAFE OPERATING PRACTICES

ASSEMBLY INSTRUCTIONS

UNPACKING

Steps for removing the snowthrower from its packaging and preparing it.

LOOSE PARTS

Information about shear pins included for auger protection.

ASSEMBLE UPPER AND LOWER HANDLE

Instructions for connecting the upper and lower handle sections.

ASSEMBLE DISCHARGE CHUTE

Steps for attaching the discharge chute to the auger housing.

SPECIFICATIONS

FUNCTIONAL DESCRIPTION

KNOW YOUR SNOWTHROWER

Labels and descriptions of the snowthrower's main components.

HEADLIGHT

Explanation of the headlight's operation and activation.

SAFETY IGNITION KEY

Details on the security key for starting and stopping the engine.

DRIVE CONTROL / AUGER CONTROL LOCK

How to engage wheel drive, auger control, and the lock feature.

CHUTE TILT CONTROL LEVER

Operation of the lever to adjust the snow discharge distance.

AUGER CONTROL

How to engage and disengage the auger for snow throwing.

SHIFT LEVER

Explanation of the shift lever for selecting forward/reverse speeds.

CHUTE DIRECTIONAL CONTROL

How to operate the control to change snow discharge direction.

SKID SHOE

Information on adjusting skid shoes for varying terrain.

OPERATING PROCEDURES

BEFORE STARTING

Pre-operation checks including gas and oil fill-up.

ELECTRIC STARTER

Steps for starting the engine using the electric starter.

RECOIL STARTER

Manual procedure for starting the engine using the pull cord.

TO STOP ENGINE

Instructions for safely stopping the engine.

TO ENGAGE WHEEL DRIVE

How to engage the forward and reverse drive mechanisms.

TO ENGAGE AUGERS

How to activate the auger for snow throwing.

AUGER CONTROL TEST

Procedure to test and adjust the auger control engagement.

CLEAN-OUT TOOL

How to safely use the clean-out tool for the chute.

OPERATING TIPS

Recommendations for efficient snow removal and machine care.

ADJUSTMENT

AUGER CONTROL

Reference to the test procedure for adjusting the auger control.

DRIVE CONTROL AND SHIFT LEVER

Steps to check and adjust drive control and shift lever engagement.

SHIFT ROD ADJUSTMENT

Procedure for adjusting the shift rod for proper gear selection.

SKID SHOES

How to adjust skid shoes for different snow conditions.

CARBURETOR

Brief mention of minor carburetor adjustments.

MAINTENANCE

LUBRICATION

Details on lubricating the engine, gear shaft, and other components.

Auger Shaft

Lubrication instructions for the auger shaft and bearings.

Auger Bearings

Seasonal lubrication for auger bearings.

Drive and Shifting Mechanism

Lubrication points for drive and shifting components.

Drive/Auger Control Lock

Lubrication of control rod cams.

SERVICING

ENGINE

Reference to the engine manual for maintenance procedures.

AUGERS

Information on shear pins and auger operation.

SHAVE PLATE AND SKID SHOES

Checking and replacing wear items like shave plate and skid shoes.

OFF-SEASON STORAGE

Proper procedures for storing the snowthrower for extended periods.

Murana WSG112 User Manual

Table of Contents

Questions and Answers:

Murana WSG112 Specifications

Summary

IMPORTANT SAFE OPERATING PRACTICES

ASSEMBLY INSTRUCTIONS

UNPACKING

LOOSE PARTS

ASSEMBLE UPPER AND LOWER HANDLE

ASSEMBLE DISCHARGE CHUTE

SPECIFICATIONS

FUNCTIONAL DESCRIPTION

KNOW YOUR SNOWTHROWER

HEADLIGHT

SAFETY IGNITION KEY

DRIVE CONTROL / AUGER CONTROL LOCK

CHUTE TILT CONTROL LEVER

AUGER CONTROL

SHIFT LEVER

CHUTE DIRECTIONAL CONTROL

SKID SHOE

OPERATING PROCEDURES

BEFORE STARTING

ELECTRIC STARTER

RECOIL STARTER

TO STOP ENGINE

TO ENGAGE WHEEL DRIVE

TO ENGAGE AUGERS

AUGER CONTROL TEST

CLEAN-OUT TOOL

OPERATING TIPS

ADJUSTMENT

AUGER CONTROL

DRIVE CONTROL AND SHIFT LEVER

SHIFT ROD ADJUSTMENT

SKID SHOES

CARBURETOR

MAINTENANCE

LUBRICATION

Auger Shaft

Auger Bearings

Drive and Shifting Mechanism

Drive/Auger Control Lock

SERVICING

ENGINE

AUGERS

SHAVE PLATE AND SKID SHOES

OFF-SEASON STORAGE

WARRANTY

TROUBLESHOOTING

PARTS LIST

SCHEMATIC DRAWING / SCHÉMA