EasyManua.ls Logo

MW TOOLS SH125-R - User Manual

MW TOOLS SH125-R
31 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SH125/300/500-R - NLFREN - v1.0 - 27062016
HANDLEIDING - MODE D’EMPLOI - MANUAL
SH125-R (758613085)
SH300-R (758613090)
SH500-R (758613095)
Elektrische takel
Treuil électrique
Electric hoist
P.02 Gelieve te lezen en voor later gebruik bewaren
P.09 Veuillez lire et conserver pour consultation ultérieure
P.16 Please read and keep for future reference
FR
EN
NL
copyrighted document - all rights reserved by FBC

Table of Contents

Questions and Answers

  • D
    David HallAug 10, 2025
    Why won't my MW TOOLS SH125-R motor turn on?
    • C
      cardenasbrittanyAug 10, 2025
      Your MW TOOLS Chain Hoists motor might not be turning on for several reasons: it may not be plugged into the power supply, so ensure it is properly connected. The wires could be broken or ripped, requiring you to check and plug them in again. There might be a switch malfunction, in which case you should repair or replace the switch. The capacitor could be burned through, necessitating a capacitor replacement. The end-switch may not have been reset or there could be a limit switch error, so check the end-switch and replace the limit switch if needed. Finally, the thermal switch might have a wire break; wait for the item to cool down or replace the thermal switch.
  • C
    Courtney WilliamsAug 15, 2025
    What to do if my MW TOOLS SH125-R Chain Hoists machine noise becomes louder?
    • J
      Jimmy WrightAug 15, 2025
      If the noise of your MW TOOLS Chain Hoists becomes louder, it could be due to several reasons. The machine might be badly oiled, requiring you to officially oil/grease it. After long use, the cogwheel and bearings could be damaged, suggesting you change the cogwheel or bearings. It could also be badly installed or dent, so check installed parts or let a qualified technician do it.
  • G
    graymondAug 19, 2025
    What to do if my MW TOOLS SH125-R Chain Hoists dual-direction switch has been activated but the motor is very loud and cannot pick up the load?
    • S
      Sally RamirezAug 19, 2025
      If your MW TOOLS Chain Hoists motor is very loud but cannot pick up the load after activating the dual-direction switch, it could be due to a few reasons. The voltage offered might be too small, so adjust the work depending on the power supply. The capacitor might be damaged, requiring a power supply change. Alternatively, the brake might not be completely open, in which case you should allow the machine to be repaired by a qualified repair service.
  • J
    Jeffrey GutierrezAug 25, 2025
    What to do if my MW TOOLS Chain Hoists rope winch has too much voltage?
    • J
      Jeremy StewartAug 26, 2025
      If your MW TOOLS Chain Hoists rope winch has too much voltage, it could be due to an earthed error or it is not properly earthed, so check earthed wires and properly connect them. Alternatively, the internal connectors might be touching the housing, so check all internal connections.
  • B
    Brianna TateAug 29, 2025
    What to do if my MW TOOLS SH125-R end-switch is not functioning?
    • C
      Catherine AlvaradoAug 30, 2025
      If the end-switch of your MW TOOLS Chain Hoists is not functioning, it could be because the end-switch is defective, so switch off or change it. It might also be blocked, in which case you should check, repair, and change the end switch.
  • G
    Garrett FisherSep 3, 2025
    What to do if my MW TOOLS SH125-R Chain Hoists brakes do not hold or the machine slips down after a power loss?
    • S
      smithbrandySep 3, 2025
      If the brakes of your MW TOOLS Chain Hoists do not hold or the machine slips down after a power loss, it could be because the air between the brakes is too large. In this case, allow the machine to be repaired by a qualified repair service.

MW TOOLS SH125-R Specifications

General IconGeneral
BrandMW TOOLS
ModelSH125-R
CategoryChain Hoists
LanguageEnglish