NaanDanJain Dan Fogger

Questions and Answers

P
Patrick AndersenAug 3, 2025
Why is there excessive wear in my NaanDanJain Irrigation System?
- S
  Suzanne BlanchardAug 3, 2025
  Excessive wear in your NaanDanJain Irrigation System can be caused by unfiltered water. To resolve this, install proper filtration. It can also result from injecting abrasive chemicals; in this case, perform a Jar test for chemical precipitation. Using harsh chemicals can also cause excessive wear, check with PCA or CCA for compatibility with your irrigation system. Finally, excessive use due to an under-designed system can be a factor.
T
Teresa AllenAug 8, 2025
How to fix a wide wetting pattern in NaanDanJain Irrigation System?
- W
  Wendy GarrisonAug 8, 2025
  A wide wetting pattern in your NaanDanJain Irrigation System can be due to excessive pressure. Check the lateral/system pressure to resolve this. Alternatively, there might be foreign matter in the nozzle. If so, take the sprinkler apart and clear the debris.
E
edwardsrobertAug 13, 2025
What to do if my NaanDanJain Irrigation System is plugging?
- B
  Barbara NunezAug 13, 2025
  If your NaanDanJain Irrigation System is experiencing plugging, it might be due to improper filtration. In this case, you should refer to the sprinkler filtration requirements. Improper maintenance can also cause plugging, so refer to the maintenance guide. Finally, plugging may also be caused by insect nesting. If this is the case, clean the nozzle.
J
jacobromeroAug 18, 2025
Why is my NaanDanJain Irrigation System misting?
- M
  Michael WilsonAug 19, 2025
  Misting in your NaanDanJain Irrigation System can occur due to low pressure. Check the lateral/system pressure to address this. It can also be caused by foreign matter in the LPD/Nozzle. If that's the case, take the Fogger/LPD apart and clear any debris.
B
Brendan WilsonAug 23, 2025
What causes a narrow pattern in NaanDanJain Irrigation System?
- A
  Ana BurnsAug 23, 2025
  A narrow pattern in your NaanDanJain Irrigation System could be due to inlet pressure being below specification, so check the lateral/system pressure. Another cause could be plugging, in which case you should clean the nozzle. Finally, excessive wear can also cause a narrow pattern; refer to the section about excessive wear.
E
emma86Aug 28, 2025
How to stop excessive dripping in NaanDanJain Irrigation System?
- N
  Nancy CobbAug 28, 2025
  Excessive dripping in your NaanDanJain Irrigation System can be caused by improper assembly. Ensure the sprinkler is properly assembled. Also, inspect for damaged components (freezing, mechanical, pest, etc.) and replace broken components or the entire sprinkler if necessary.

Summary

Dan Fogger;Mister Introduction

Product Features

Details the key advantages and characteristics of the Dan Fogger/Mister system for greenhouse applications.

Applications Overview

Product Technical Specifications

Dan Fogger Specifications

Presents technical specifications for the Dan Fogger, including models, flow rates, and pressure requirements.

Green Mist Specifications

Outlines technical specifications for the Green Mist models, detailing GPH, height, and pressure.

Selection and Ordering Information

Detailed Application Areas

Regular Maintenance Schedule

Routine Maintenance Steps

Scheduled & Preventative Maintenance

Scheduled Maintenance Tasks

Preventative Maintenance Actions

Troubleshooting Common Issues

Pattern Uniformity Troubleshooting

Provides solutions for wide or narrow wetting patterns caused by pressure, foreign matter, or wear.

Misting, Wear, and Dripping Issues

Offers fixes for excessive misting, component wear, and dripping issues related to pressure, filtration, and assembly.

Nozzle Plugging Solutions

Guides on resolving nozzle plugging due to filtration, maintenance, or insect nesting.