NANOLUX LED SN720 Pro

To Next Page

The fixture is suitable for indoor environment. Do not install your fixture in wet or

outdoor environment. Do not operate the fixture close to combustible materials. The

fixture will get hot during operation. Do not touch the fixture during or right after

operation. Make sure the power cord does not touch any hot part of the fixture. Make

sure the light bars are clean and inserted correctly. The normal operating environment

temperature should be below 104°F. Exceeding the maximum environmental

temperature will stress electronic components, which will lead to shorter lifetime and

decreased reliability.

● Comply with local installation regulations.

● Store the fixture in a dry and clean environment, with an ambient temperature of

-10°C ~ 50°C and ambient humidity of less than 90% RH. It is recommended that

the fixture shall not stay unused for more than six months. If it has stayed unused for

more than six months, please test to ensure fixture is functioning at 100%.

● Please keep products safe. Avoid mechanical pressure, excessive vibration and

dropping the unit during the process of assembly to protect the light bar and track.

● Keep away from water, oil and organic solvent, or it will reduce the efficacy and have

the potential risk of electric leakage.

● All equipment, devices and machines shall be effectively grounded.

● Regularly check and clean the dust from LED array.

1. Disconnect from power supply before general care.

2. Remove the dust from the light bar by using low-pressure compressed air.

3. Clean the diode array with a soft cloth to prevent it from being scratched.

4. Be sure not to touch the diode with your bare hands, even after the LED is

disconnected from power supply.

● It is recommended that you contact a licensed electrician or an expert if any of the

following happens:

1. The cable or the plug has been damaged.

2. The unit has been exposed to rain.

3. Significant changes in the unit performance.

4. Fixture or light bar dropped and corner of its enclosure got bent.

● There are no serviceable parts inside the LED. Opening the LED will void its

warranty.

Nanolux warrants manufacturing defects of this product if it is used under normal

operating conditions for a period of five (5) years from the original date of purchase. If

the product shows manufacturing defects within this period and that defect is not

caused by user error or improper use, Nanolux shall, at its discretion, either replace or

repair the product by using applicable new or refurbished parts. For any service,

return the product to your shop along with the original sales receipt.

SCOPE OF USE AND MAINTENANCE

ALWAYS COMPLY WITH LOCAL

INSTALLATION REGULATIONS AND CODES

OPERATING

MANUAL

LED SN630&720

&830&1000 Pro

LED SN630 Pro (6 light bars)

LED SN720 Pro (8 light bars)

LED SN830 Pro (8 light bars)

LED SN1000 Pro (10 light bars)

NCCS-RTU/0-10V COMPATIBLE

WARRANTY

TROUBLE SHOOTING

Problem

One or more

fixtures are

completely off.

Disconnect from power source.

Broken cable or wire connecting

controller to fixture or wire

connecting fixture to fixture.

The power supply settings do

not match with local AC

voltage and frequency.

Make sure power is on and

cables are plugged in.

Dimming

failure

LED will not

come on.

Probable cause(s)

Possible fixes or

corrective maintenance

Repair or replace any

damaged cables if necessary.

Disconnect fixture from the

power supply. Check settings

and correct if necessary.

-04-

Made in China

PATENTED PRODUCTS, COUNTERFEITING NOT ALLOWED.

This model is compatible with NCCS-RTU/0-10V. When using the function, please

press the

DIM mode selection button to show 0.

Insert telephone wire into the jack of the fixture and 0-10V Lighting Controller, and

then Dimming function on the LED fixture is enabled.

● Maximum of 120 units can be controlled by 0-10V Lighting Controller.

● Simulate sunrise and sunset for dimming.

● Turn off the device automatically following the setting time and temperature.

In & Out jacks included on the fixture allows for multi-fixtures connected in parallel.

DIMMING FUNCTION

CAUTION:

Max 60 Units

LED

LED LED LED

LED LED

RTU is removed from the fixture during operation, the fixture will automatically turn off

after 10 seconds. If the RTU loses communication with the DTU for any reason, the

fixture will automatically turn off after 10 minutes. If the fixture continues to turn off for

any reason during operation with the RTU in NCCS mode, replace the RTU and

confirm it is communicating with the DTU.

For further NCCS RTU customer support and tech support pages, visit www.

nanoluxtech.com.

When using 0-10V Lighting controller, please insert 0-10V module control wire into the

RJ11 jack of a Nanolux fixture. If 0-10V Lighting controller loses communication with

fixture due to some type of errors, especially resulting from short circuit, fixture will

shut off automatically in 5 seconds. Fixture will turn back on if errors are fixed.

After installation, verify installation was a success by cycling the lights on/off a few

times, by setting 'over temperature shut down' to a low value like 85°F, and rubbing the

temperature probe with your fingers, tricking the 0-10V Lighting controller/NCCS RTU

into an over temperature condition and shutting the lights off. Then leave the probe

alone, and after recommended 10-15 minutes the 0-10V Lighting controller/ NCCS

RTU should turn all the lights back on.

For detailed instructions, please refer to 0-10V Lighting Controller operating manual.

PRODUCT PACKING LIST

Folding Fixture

YO-Ratchet

Telephone Wire

Operating Manual

NameNo. Quantity

B C D

Manual

Need help?

Do you have a question about the NANOLUX LED SN720 Pro and is the answer not in the manual?

Summary

Local Installation Regulations and Codes Compliance

Dimming Functionality Overview

Dimming Control and Compatibility

Explains NCCS-RTU/0-10V compatibility, max units, and sunrise/sunset simulation.

Scope of Use and Maintenance Guidelines

General Care and Cleaning Instructions

Instructions for cleaning the LED array using compressed air and soft cloth.

When to Seek Professional Assistance

When to seek professional help for damaged cables, exposure to rain, or performance changes.

Installation and Usage Instructions

Technical Specifications

Model Specifications Summary

Detailed technical specifications for SN630, SN720, SN830, and SN1000 Pro models.

Product Component Identification

Button Function Instructions

DIM Mode Selection Operation

How to select dimming ratios (0-100) and control modes (local/remote).

UV Timing Selection Control

Controls UV diode timing, including follow white, off, and timed shutoff (1-12 hours).

IR Timing Selection Control

Controls IR diode timing, including follow white, off, and timed shutoff (1-12 hours).

Fixture Assembly and Hanging Guide

Fixture Hanging Procedure

Steps for unpacking, unfolding the track, attaching ratchets, and hanging the fixture.

This document describes the Nanolux LED SN630, SN720, SN830, and SN1000 Pro series operating manual, which are NCCS-RTU/0-10V compatible fixtures.

Function Description

These LED luminaires are designed for indoor use and offer advanced dimming capabilities. They are compatible with the NCCS-RTU/0-10V lighting controller, allowing for precise control over light output. The fixtures support a wide range of dimming ratios from 30% to 100% and can simulate sunrise and sunset. They also feature automatic shutdown based on set time and temperature, and include UV and IR timing functions for specialized growing needs. The in and out jacks enable parallel connection of multiple fixtures.

Important Technical Specifications

The series includes four models: SN630 Pro, SN720 Pro, SN830 Pro, and SN1000 Pro, all operating on an AC120-277V input voltage at 50/60Hz.

LED SN630 Pro:

Input Power: 630W
Efficacy: 2.9µmol/J
Light Output PPF: 1830µmol/s
Spectrum: WHITE+UV+IR Spectrum
Dimension / Weight: 44.7x43.7x2.4inch / 19.2lbs (1135x1110x60mm / 8.7kgs)
Dimming: Manual DIM 30%-100%, NCCS-RTU/0-10V compatible
Light Distribution: 120°
Lifetime: ≥50,000hrs

LED SN720 Pro:

Input Power: 720W
Efficacy: 2.9µmol/J
Light Output PPF: 2090µmol/s
Spectrum: WHITE+UV+IR Spectrum
Dimension / Weight: 44.7x43.7x2.4inch / 22.5lbs (1135x1110x60mm / 10.2kgs)
Dimming: Manual DIM 30%-100%, NCCS-RTU/0-10V compatible
Light Distribution: 120°
Lifetime: ≥50,000hrs

LED SN830 Pro:

Input Power: 830W
Efficacy: 2.9µmol/J
Light Output PPF: 2410µmol/s
Spectrum: WHITE+UV+IR Spectrum
Dimension / Weight: 44.7x43.7x2.4inch / 22.5lbs (1135x1110x60mm / 10.2kgs)
Dimming: Manual DIM 30%-100%, NCCS-RTU/0-10V compatible
Light Distribution: 120°
Lifetime: ≥50,000hrs

LED SN1000 Pro:

Input Power: 1000W
Efficacy: 2.9µmol/J
Light Output PPF: 2900µmol/s
Spectrum: WHITE+UV+IR Spectrum
Dimension / Weight: 44.7x43.7x2.4inch / 27.8lbs (1135x1110x60mm / 12.6kgs)
Dimming: Manual DIM 30%-100%, NCCS-RTU/0-10V compatible
Light Distribution: 120°
Lifetime: ≥50,000hrs

All specifications are subject to change without notice, with a tolerance of ±10%.

Usage Features

Dimming Function: The fixtures are compatible with the NCCS-RTU/0-10V controller. To enable dimming, press the DIM mode selection button to show '0' and connect a telephone wire from the fixture to the 0-10V Lighting Controller.

Up to 120 units can be controlled by a single 0-10V Lighting Controller.
Simulates sunrise and sunset.
Automatic device shutdown based on set time and temperature.
In & Out jacks allow for parallel multi-fixture connections.

Button Function Instructions: The device features a digital display and several buttons for control:

DIM mode selection button: Allows selection of dimming ratios from 30 to 100, or '0' for NCCS-RTU/0-10V/OFF function. Pressing the button cycles through options; holding it for over 2 seconds changes values every 0.3 seconds. If an external control signal is present, the dimming ratio is controlled externally. If no external signal is connected, the fixture will shut down after 10 seconds (or 3 seconds if no operation is performed).
UV timing selection button: Controls UV diode operation with options from 0 to 12 hours, or 'FL' (Follow White). 'FL' means UV diodes follow white diodes. '0' means UV off. 1-12 hours means UV diodes turn off after the set time. Timing is based on a 24-hour cycle, with a maximum of 12 hours. The UV diode will re-light every 24 hours. To change the timing reference, set UV to 0, then reset the timing. Timing stops if the DIM dimming ratio is 0.
IR timing selection button: Similar to UV timing, controls IR diode operation with options from 0 to 12 hours, or 'FL' (Follow White). 'FL' means IR diodes follow white diodes. '0' means IR off. 1-12 hours means IR diodes turn off after the set time. Timing is based on a 24-hour cycle, with a maximum of 12 hours. The IR diode will re-light every 24 hours. To change the timing reference, set IR to 0, then reset the timing. Timing stops if the DIM dimming ratio is 0.

Digital Tube Screensaver Function:

The digital display turns off when DIM mode selects '0'. If an external control signal is connected and stable, or if no external control signal is connected and no button is pressed, the display will turn off after 5 seconds.
The display wakes up with any button operation or change in external control signal.

Assembly Instructions:

Unpack the fixture.
Unfold the fixture track and place it with the diode array facing downward.
Attach carabiners from the YO-Ratchets to the ring bolts.
Hang the fixture in the desired location, ensuring it is level. The recommended mounting height is 8"-20" (20cm-50cm) above the canopy for optimal light efficiency and uniformity. Growers should monitor canopy temperature to adjust height as needed.

Maintenance Features

Scope of Use and Maintenance:

Comply with local installation regulations and codes.
Store the fixture in a dry, clean environment with ambient temperature of -10°C to 50°C and humidity below 90% RH.
If unused for more than six months, test to ensure 100% functionality.
Avoid mechanical pressure, excessive vibration, and dropping the unit during assembly to protect the light bar and track.
Keep away from water, oil, and organic solvents to prevent reduced efficacy and electric leakage.
All equipment must be effectively grounded.
Regularly check and clean dust from the LED array:
1. Disconnect from power supply.
2. Remove dust from the light bar using low-pressure compressed air.
3. Clean the diode array with a soft cloth, avoiding scratches.
4. Do not touch the diode with bare hands, even when disconnected from power supply.
Contact a licensed electrician or expert if the cable/plug is damaged, the unit has been exposed to rain, performance changes significantly, or the fixture/light bar is dropped and bent.
There are no serviceable parts inside the LED. Opening the LED will void its warranty.

Troubleshooting:

Fixture completely off: Check power source connection and ensure cables are plugged in.
Dimming failure: Repair or replace damaged cables connecting the controller to the fixture or fixtures to each other.
LED will not come on: Disconnect from power supply, check, and correct local AC voltage and frequency settings.

Warranty: Nanolux provides a five (5) year warranty against manufacturing defects under normal operating conditions from the original date of purchase. If a defect occurs within this period due to manufacturing issues (not user error or improper use), Nanolux will, at its discretion, replace or repair the product using new or refurbished parts. For service, return the product to the shop with the original sales receipt.