What to do if the Nanosonics Trophon EPR chamber door is open and locked?
If the chamber door of the Nanosonics Laboratory Equipment is open and locked, try selecting Restart on the LCD if the trophon is in sleep mode. Otherwise, power the trophon off and back on using the power switch. If this doesn't work, power off the trophon and follow section C4.3. Close the chamber door before powering the trophon back on.
Why is my Nanosonics Medical Equipment beeping?
If your Nanosonics Medical Equipment is beeping, follow the instructions on the screen. There might be a probe inside the device that needs to be removed.
What to do if the chamber door will not open on Nanosonics Medical Equipment?
If the chamber door on your Nanosonics Medical Equipment won't open, ensure the device has power. Follow any on-screen messages for instructions and confirm that any ongoing cycle (purge or disinfection) is complete. Also, check that the chamber door handle can be completely opened.
Why will the cycle not start on my Nanosonics Medical Equipment?
If your Nanosonics Medical Equipment does not start the cycle, make sure the device has power and follow the instructions on the screen. Check that the probe is correctly loaded and the chamber door is closed. If you are at the ‘Clean and dry probe screen’ and the YES button will not register, or if the screen reads READY and the start button will not respond, contact your customer service representative.
How to troubleshoot power issues with Nanosonics Medical Equipment?
If there is no power to your Nanosonics Medical Equipment, ensure that the device is plugged in and that you are using the correct power cable for your region. Also, make sure the power is switched ON at the wall outlet and that the power switch on the device is set to ON.
What to do if the chamber door is open and locked on Nanosonics Medical Equipment?
If the chamber door on your Nanosonics Medical Equipment is open and locked, try selecting RESTART on the LCD screen if the device is in sleep mode. Otherwise, power the device OFF and then back ON using the power switch. This should automatically unlock the chamber door. If these steps don't work, power OFF the device and manually override the door lock. Close the chamber door before powering the device back ON.
What to do if the Nanosonics Laboratory Equipment is failing numerous cycles?
If the Nanosonics Laboratory Equipment is failing numerous cycles, record any error codes and the color of the chemical indicator, and then contact your customer service representative.
How to troubleshoot no power to Nanosonics Trophon EPR trophon?
Ensure the Nanosonics Laboratory Equipment trophon is completely plugged in and switched ON at both the trophon power switch and at the wall outlet. Also, verify that the correct power cable for your region is being used.
How to fix a Nanosonics Trophon EPR Laboratory Equipment chamber door that won't open?
If the chamber door of your Nanosonics Laboratory Equipment will not open, ensure that the trophon has power and that there is no disinfection, warm-up, or purge cycle running.
What to do if liquid is leaking from the Nanosonics Laboratory Equipment trophon?
If you see liquid or mist coming from the Nanosonics Laboratory Equipment trophon, do not come into contact with it. Wear appropriate PPE and ensure the area is well ventilated. Allow the trophon to complete the cycle, then turn it off and remove the power cord. Contact your customer service representative.
Provides general information about the trophon EPR, including validated probes and user training requirements.
Details critical warnings, labels, and symbols associated with the trophon EPR for safe operation.
Describes the front, back, chamber, and side panels of the trophon EPR device, identifying key components.
Covers the essential steps for installing the trophon EPR, including positioning, cable management, powering on, and basic settings.
Explains how to handle and load the disinfectant cartridges, including safety precautions and spillage procedures.
Details the process for performing a high-level disinfection cycle, including probe preparation and positioning.
Outlines the reasons for and procedure to run a purge cycle to remove disinfectant and prepare the device for transport.
Provides instructions for safely removing and disposing of used disinfectant cartridges, including handling precautions.
Addresses common issues like power failure or cycle faults, offering solutions and guidance for troubleshooting.
Describes periodic cleaning procedures and when to contact for device service.
Explains the process for decommissioning and disposing of the trophon EPR unit.
Introduces the trophon Printer, its features, and initial setup procedures.
Covers replacing the label roll and cleaning the trophon Printer.
Provides guidance on connecting/disconnecting the printer and troubleshooting error messages.
Information on proper disposal of the trophon Printer for EU member states.
Details how to reorder trophon Printer supplies like the printer, cables, and label rolls.
Lists the electrical, environmental, physical, and safety specifications for the trophon Printer.
Provides detailed technical specifications for the trophon EPR, including electrical, environmental, physical, and EMC compliance.
Contains information on the product warranty terms, conditions, and the registration form.
General| Brand | Nanosonics |
|---|---|
| Model | Trophon EPR |
| Category | Laboratory Equipment |
| Language | English |
To Next Page