National Cycle VStream N20014 User Manual

10mm Box Wrench
5mm Hex Key
Phillips Screw Driver
PARTS LIST
Index Description Qty.
1 Windscreen, Quantum Hardcoated polycarbonate 1
With RainZip treatment
2 RainZip treatment, 3oz. Bottle 1
Bag 1008
3 M6 x 16 Stainless Screws w/ Nylok 4
4 Collar L .177 4
5 Foam Pads 4
REMOVAL AND RE-INSTALLATION
Retain all fasteners and parts. Most will be re-
used. Four M6 x 16 Screws and Collars are supplied.
Installation of windscreen will be in reverse order
of removal.
Position stock windscreen in highest position.
1. Move mirror forward. Lift rubber sleeve to expose inside
attachment point. Repeat on opposite side.
2. Gently pry “bracket” over hex bolt to in order to remove
hardware holding front body panel in place. Repeat on
opposite side. Figure 1. (10mm Box Wrench)
To avoid hardware dropping into mirror cavity
stuff a small cloth under hardware! Item (A)
3. Remove hardware holding front panel in place. Repeat
on opposite side.
Attention Note
Special notes and cautionary measures
which can prevent damage to the accessory
or motorcycle.
Tips for facilitation of operation,control
and adjustment, as well as maintenance.
N20014 VStream
®
Special Edition
Windscreen for GL1800 2001~
Installation and Owner’s Manual
Quantum™ Hardcoated polycarbonate
with RainZip® Treatment
National Cycle, Inc. PO Box 158, Maywood, IL 60153-0158 USA
708-343-0400 / Fax: 708-343-0625 / www.nationalcycle.com / e mail: info@nationalcycle.com
Page 1 / 4 10-118545-000 03/10
Figure 1
Figure 2
A
Thank you for purchasing a National Cycle® product. Please read these instructions carefully and thoroughly
before beginning work. Dealers if installing this windshield for a customer please give them this manual. It con-
tains information needed to properly maintain and use this product.

National Cycle VStream N20014 Specifications

General

Brand	National Cycle
Model	VStream N20014
Category	Motorcycle Accessories
Language	English

Summary

REMOVAL AND RE-INSTALLATION

Position stock windscreen in highest position

Position stock windscreen in the highest position before proceeding with removal or installation steps.

Move mirror forward and expose attachment point

Move mirrors forward and lift rubber sleeve to expose the inside attachment point for removal.

Remove front body panel hardware

Gently pry bracket over hex bolt to remove front body panel hardware, repeating on opposite side.

Secure hardware from dropping

To avoid dropping hardware into mirror cavity, stuff a small cloth under hardware.

Position mirror back and unsnap front panel

Position mirror back and unsnap the front panel to access windscreen hardware.

Remove windscreen hardware

Remove front and side hardware holding the windscreen in place using appropriate tools.

Remove stock windscreen

Carefully remove the stock windscreen from the motorcycle after all hardware is detached.

Install foam pads and new windscreen

Install die-cut foam pads and then the VStream windscreen using supplied hardware.

APPLICATION OF RAINZIP TREATMENT

Quantum™™ hardcoat friendly

Learn about the Quantum hardcoat and RainZip repellent for screen clarity and water beading.

Reapplying RainZip treatment

Guidelines for reapplying RainZip treatment to renew water repellency after 3-5 months of use.

RainZip application steps

Detailed steps for cleaning, applying, drying, and wiping RainZip treatment for optimal results.

WINDSHIELD ADJUSTMENT

Troubleshooting limited range

Tips for troubleshooting limited windshield adjustment range, including frozen adjusters or new pads.

Adjusting the shield height

Instructions on how to lower the shield by first raising it to the highest position.

MAINTENANCE

Cleaning the windshield

Instructions for cleaning the windshield using mild soap and water, avoiding harsh chemicals.

Recommended cleaning product

National Cycle Windshield Wash (N1401) is recommended for everyday cleaning.