NEC ME403U Replacing The Lamp And The Filter

[Notice] Replacing the Lamp and the Filter
When approximately 300 hours before the lamp reaches the end of its life, the LAMP indicator
in the cabinet will blink ORANGE and the LAMP WARNING icon will appear at the top right of
the projection screen.
Even though the lamp may still be working, replace the lamp to maintain the optimal projector
performance.
After replacing the lamp and the filter, be sure to clear the lamp usage hours and the filter
usage hours.
Please refer to “
❹
Replacing the Lamp and the Filter” in the user’s manual included on the
supplied NEC Projector CD-ROM. (
→
Page 85)
Lamp life of this projector
ECO mode Normal ECO 1 ECO 2 Boost
Lamp life (hours) *
10,000 12,000 20,000 8,000
* This is not a warranty time. Repair or replacement parts may be required before the
lamp is replaced.
- Four modes of the ECO mode can be selected: [Normal], [ECO 1], [ECO 2] and [Boost]
modes.
- If you select ECO 1 or ECO 2 mode, the lamp life will be increased, while lowering
power consumption.
- If you select Boost mode, the picture becomes brighter than the Normal mode.
However, the power consumption will increase and the lamp life may also be
shortened.
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely
hot. Turn the projector off and then disconnect the power cord. Allow at least one
hour for the lamp to cool before handling.
• When removing the lamp from a ceiling-mounted projector, make sure that no one is
under the projector. Glass fragments could fall if the lamp has been burned out.
NOTE:
• Use the specified lamp for safety and performance.
To order the replacement lamp, specify your lamp type, NP47LP.
The replacement lamp comes with filters.
• DO NOT REMOVE ANY SCREWS except one lamp cover screw and three lamp housing
screws. You could receive an electric shock.
• Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the
glass surface might cause an unwanted shadow and poor picture quality.
Continued on Reverse Side

NEC ME403U Specifications

General

Native aspect ratio	16:10
Projection distance	0.75 - 12.88 m
Vertical scan range	24 - 85 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	3LCD
Contrast ratio (typical)	16000:1
Screen size compatibility	30 - 300 \
Projector native resolution	WUXGA (1920x1200)
Keystone correction, horizontal	-30 - 30 °
Projector brightness (economic mode)	3000 ANSI lumens
RMS rated power	16 W
Number of built-in speakers	1
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
Sustainability certificates	CE, ErP, RoHS, WEEE
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Lamp power	225 W
Light source type	Lamp
Lamp power (economic mode)	151 W
Service life of light source	10000 h
Service life of light source (economic mode)	20000 h
Focus	Manual
Focal length range	17.2–27.7 mm
Aperture range (F-F)	1.5 - 2.08
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	305 W
Power consumption (standby)	0.5 W
Power consumption (typical)	- W
Power consumption (economy mode)	220 W
Video color modes	DICOM simulation mode
Analog signal format system	NTSC, PAL, PAL 60, SECAM
Supported graphics resolutions	1920 x 1200 (WUXGA), 3840 x 2160
DVI port	No
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	37 dB
Number of OSD languages	29
Noise level (economic mode)	29 dB
Harmonized System (HS) code	85286200

Weight and Dimensions

Depth	261 mm
Width	345 mm
Height	104.6 mm
Weight	3500 g