nedis WCPD18WU102BK User Manual

a
Quick start guide
USB-C Wall Charger
WCPD18WU102BK /
WCPD18WU102WT
For more information see the extended manual online:
ned.is/wcpd18wu102bk | ned.is/wcpd18wu102wt
Intended use
The USB wall charger is intended to charge tablets, smartphones
and many other USB devices, without requiring a PC or notebook.
The USB charger converts voltages from 100 to 240 VAC into 5.0
VDC - 12.0 VDC and is very convenient at oces, at home or during
travels.
The product is intended for indoor use only.
The product is not intended for professional use.
Any modication of the product may have consequences for safety,
warranty and proper functioning.
Specications
Product USB-C Wall Charger
Article number WCPD18WU102BK /
WCPD18WU102WT
Input voltage 100 - 240 VAC
Input AC frequency 50/60 Hz / 0.5 A
Output voltage 5.0 VDC / 9.0 VDC / 12.0 VDC
Output current 3.0 A / 2.0 A / 1.5 A
Output power 15 W / 18 W / 18 W
Average active eciency 81.29 %
Eciency at low load (10 %) 73.09 %
No-load power consumption 0.08 W
Main parts (image A)
1 USB charging port 2 Interchangeable plug
Safety instructions
-
WARNING
• Ensure you have fully read and understood the instructions in this
document before you install or use the product. Keep the
packaging and this document for future reference.
• Ensure you have fully read and understood the instructions in this
document before you install or use the product. Keep this
document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace a
damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualied technician for
maintenance to reduce the risk of electric shock.
• Do not expose the product to water or moisture.
• Disconnect the product from the power source and other
equipment if problems occur.
• Always check that the voltage of the product corresponds to the
mains voltage.
• Do not unplug the product by pulling on the cable. Always grasp
the plug and pull.
• Unplug the product when your device is charged or if you do not
plan on using the product for an extended period of time.
• The power outlet shall be located near the product and shall be
easily accessible.
• Never use a damaged or faulty USB cable for charging. This this
can damage the product and harm your device.
• Stop the charging process if the product gets too warm.
Using the product
1. Connect the charger into the power outlet.
2. Insert a USB cable into the USB charging port and the other end
to the device you want to charge.
3. Unplug the charger when it is not in use.
c
Kurzanleitung
USB-C Wandladegerät
WCPD18WU102BK /
WCPD18WU102WT
Weitere Informationen nden Sie in der erweiterten
Anleitung online: ned.is/wcpd18wu102bk |
ned.is/wcpd18wu102wt
Bestimmungsgemäße Verwendung
Das USB-Wandladegerät ist zum Auaden von Tablets, Smartphones
und vielen anderen USB-Geräten gedacht, ohne dass ein PC oder
Notebook erforderlich ist. Das USB-Ladegerät wandelt Spannungen
von 100 bis 240V in 5,0 VDC - 12,0 VDC um und ist sehr praktisch in
Büros, zu Hause oder auf Reisen.
Das Produkt ist nur zur Verwendung innerhalb von Gebäuden
gedacht.
Das Produkt ist nicht für den professionellen Einsatz gedacht.
Jegliche Modikation des Produkts kann Folgen für die Sicherheit,
Garantie und ordnungsgemäße Funktionalität haben.
Spezikationen
Produkt USB-C Wandladegerät
Artikelnummer WCPD18WU102BK /
WCPD18WU102WT

nedis WCPD18WU102BK Specifications

General

Brand	nedis
Model	WCPD18WU102BK
Category	Battery Charger
Language	English