Nelson SC45A WS - User Manual

Questions and Answers

B
Breanna RodriguezAug 20, 2025
Why is the Nelson Washer not starting when switched on?
- J
  Joseph MorganAug 21, 2025
  If your Nelson Washer isn't starting when you turn it on, several factors could be at play. First, check if there's voltage in the electrical system, ensure the main switch is connected, and verify that the fuses are intact. The machine's connecting cable might be damaged and need replacement. Also, inspect the conductors in the control panel terminal board, and tighten them if they're loose. The machine line switch or conductor contacts may be inefficient and require replacement. The door micro might be faulty, so replace it if necessary. Finally, check the connection of the electronic board, and replace the board if necessary.
A
Angela WelchAug 23, 2025
What to do if the Nelson Washer dishes are not clean?
- D
  David CamachoAug 23, 2025
  If dishes are not clean after a wash cycle in your Nelson Washer, consider these possibilities: The electric pump may be faulty or damaged. The detergent might not be suitable for dishwashers, so ensure you're using a product specifically formulated for industrial washing. Also, check that there is enough detergent in the bowl and always adhere to the doses stated on the product technical sheets. The impellers could be obstructed or damaged, requiring cleaning or replacement. Finally, the washing impeller may be blocked, so check and unblock it.
J
Joshua LindseyAug 26, 2025
What to do if water does not enter Nelson Washer?
- D
  Danielle EdwardsAug 26, 2025
  If water isn't entering your Nelson Washer, check the following: Ensure there is water in the water system and the tap is open. Inspect the supply pipe for bends or compressions. Remove and clean the solenoid valve filter if it's dirty. If the solenoid valve coil is broken, replace it. Also, remove and check the small piston of the solenoid valve. Check all connections on the circuit and replace the pressure switch if it's faulty. Finally, check the connection of the electronic board, and replace the board if necessary.
A
Amber FreemanAug 27, 2025
Why the Nelson SC45A WS does not rinse?
- D
  Dominique HensleyAug 27, 2025
  If your Nelson Washer isn't rinsing, check these potential issues: Ensure there's water in the system and the tap is fully open. Inspect the supply pipe for any bends or squeezes. Remove and clean the solenoid valve filter if it's dirty. If the solenoid valve coil is interrupted, replace it. Remove and check the small piston of the solenoid valve. Also, ensure the system pressure is at least 2 bar; if it's lower, consider installing an auxiliary rinse pump.
R
Richard SmithAug 30, 2025
What to do if the Nelson Washer rinses uninterruptedly?
- E
  Eric LongAug 30, 2025
  If your Nelson Washer rinses continuously, it could be due to a dirty solenoid valve. Try removing the solenoid valve and cleaning the membrane compensation cutout, replacing the valve if it's sealed. The membrane may also be torn, requiring replacement. Additionally, the small piston might not be moving properly or is blocked, so check and replace the solenoid valve if needed. Finally, check the connection of the electronic board, and replace the board if necessary.
M
Megan ZunigaSep 1, 2025
What causes the water in the boiler and/or bowl of a mono-phase Nelson Washer not to heat up?
- P
  Pamela AdamsSep 1, 2025
  If the water in the boiler or bowl of your mono-phase Nelson Washer isn't heating up, several components could be faulty. The boiler thermostat, bowl thermostat, or safety thermostat might need replacement. The pressure switch contact could be faulty and require replacement. The safety thermostat might have failed to cut in, so reset it and check for the cause of the anomaly. Check the connections and conductors for any faults. The boiler or bowl heating element may also be damaged and require replacement.
J
Jonathan AdamsSep 3, 2025
What causes the water in the boiler and/or bowl of a tri-phase Nelson SC45A WS Washer not to heat up?
- R
  Rachel JarvisSep 3, 2025
  If the water in the boiler or bowl of your tri-phase Nelson Washer isn't heating up, here are some potential causes: A phase might be missing from the relay coil, so check it. The relay coil itself could be interrupted, also requiring a check. The boiler thermostat or pressure switch contacts might be faulty and need replacement. The relay contacts may be worn out, necessitating replacement of the contactor. Check the connections and conductors for faults. Ensure there isn't a missing phase in the appropriate circuit. The boiler heating element could be damaged and need replacement. Lastly, verify that the connection between the terminals and the heating element is correct.
K
Kristen AllenSep 6, 2025
What to do if the electric dispenser of the detergent in Nelson SC45A WS Washer is faulty?
- M
  Matthew BlackwellSep 6, 2025
  If the electric detergent dispenser in your Nelson Washer is faulty, the small tube inside the dispenser may be broken, requiring replacement. Alternatively, the small suction tube might be bent or damaged, so check it and replace it if necessary.
Y
Yvonne MooreSep 8, 2025
What causes the water in the boiler and/or bowl of the Nelson SC45A WS to overheat?
- J
  James ThompsonSep 8, 2025
  If the water in the boiler or bowl of your Nelson Washer is overheating, the contacts in the boiler or bowl thermostat might be locked in the “Closed” position, requiring replacement.
Y
ymackSep 12, 2025
What causes the wash electric pump of Nelson Washer to be faulty?
- C
  Cassandra KaiserSep 12, 2025
  If the wash electric pump in your Nelson Washer is faulty, the thermal protection might be disconnected and needs replacement. The door micro could also be faulty, requiring replacement. Additionally, the condenser might be faulty and need replacement, or the motor winding could be faulty and also need replacement. Finally, check the connection of the electronic board, and replace the board if necessary.