5. Storage and transportation, service life
4. Current maintenance
If during operation the device fault is detected it is necessary to call
maintenance personnel. Within the warranty period servicing and
repair are provided by the manufacturer dealer.
The devices should be stored in packing at temperatures from +5°C to
+40°C and relative humidity of not more than 80% in heated and
vented warehouses, in air-conditioned depots without corrosive
contaminants, conductible dust, acid and alkali vapors and gases
causing corrosion and insulation breakdown.
The devices should be transported packaged, in containers, closed
railway cars, heated and air-tight compartments of aircraft and holds
and by trucks with rain and snow protection for any distances at
temperatures from -50°C to +50°C and relative humidity of 100% at
25°C.
6. Disposal
At the end of the service life the device is subject to disposal. The
device does not pose a hazard to human health and environment. The
device does not contain any non-ferrous and precious metals. Waste
batteries should be disposed separately from mini remote controls.
Average service life is 5 years min.
Remote Control Radio 8101-4M (see serial number on the first page)
is manufactured in conformance with RB TR 100376351.002-
2003, is approved by QCD and is classified as fit for operation.
Guaranteed storage life is 6 months from the manufacturing date
(the last 6 figures in the product serial number, for example: 191117
– November 19, 2017).
Guarantee service life is 24 months from the date of sale.
With the note of sale absent – from the manufacturing date.
Warranty obligations cease in case of non-observance of operating
conditions established by the manufacturer and mechanical damage
during operation. Warranty obligations do not cover the case of
failure to present the device passport.
7. Manufacturer's warranty
8. Completeness
Remote Control Radio 8101-4M ......................................................1 pc.
Passport ............................................................................................1 pc.
Individual packing ..............................................................................1 pc.
9. Acceptance certificate
10. Potential problems
The remote control is not recorded in
the executive devices.
1. Battery has run down (LED is off or blinks
when you press the remote control).
2. The remote control in dynamic mode is not
recorded in the executive devices which support
only static transmissions.
1. Change battery.
2. Change the operation mode from dynamic to
static one.
2
Made in Belarus
Ver. 1
Representative offices
in Russian Federation:
15, Bolshaya Ochakovskaya St.,
119361, Moscow.
Tel.: +7 495 430-79-60
+7 495 735-64-47
info@nerosk.ru
SketchNero Group LLC
technical support:
8 800 5000-930
+375 29 609-25-59
+375 29 610-12-53
Manufacturer and representative
office in Belarus
www.neroelectronics.by
Nero Electronics LLC
Tel.: +375 17 388-53-00
technical support:
Minsk FEZ, 223016, Minsk district,
Novy Dvor Rural Council, 74
by-order@neroelectronics.by
ua-order@neroelectronics.by
+380 67 679-51-22
technical support:
21, B. Khvoyki St., Office ,
03022, Kiev.
Tel.: +38 067 679-51-22
+38 044 500-18-55
Umnye resheniya LLC
Representative office
in Ukraine:
Nero SPb LLC
14, Komsomola St., Build. 2,
195009, St. Petersburg
spb-order@neroelectronics.by
Tel.: +7 812 987-51-56
+7 981 757-90-45
technical support:
8 800 5000-930
DPM. The remote control should be programmed previously in the executive device.
1. Input the executive device into the DPM from the previously
programmed remote control: press and hold the recorded channel
button and any other button for more than 4 sec., then release both
buttons and press short the recorded button twice during 5 sec.
a) record channels of new remote controls into the memory of
executive device;
d) output the executive device from the DPM: press and hold the
previously recorded channel button of the remote control, and
then press short any other button.
2. You can perform the following actions when the executive device
is input into the DPM:
c) erase all memory of the executive device: press and hold the
recorded channel button of the remote control and any other
button for more than 4 sec.
b) delete channels of recorded remote controls from the memory
of executive device;
1. Roller shutter curtain will make a short-term movement «DOWN-
UP» once, and after 5 sec. by repeated short-term movement «DOWN-
UP» it will confirm the input in the DPM.
a) Roller shutter curtain will make long-term movement «DOWN»,
short-term movement «UP-DOWN», and long-term movement «UP».
b) Roller shutter curtain will make long-term movement
«DOWN-UP».
c) Roller shutter curtain will make long-term movement «DOWN-UP»
twice.
2. Indication on the executive device:
d) Roller shutter curtain will make short-term movement
«DOWN-UP» twice.
3. Distance Programming Mode (DPM)
To Previous Page
Loading...