Night & Day Furniture Cinnamon Futon Bunk Bed User Manual

Cinnamon Futon Bunk Bed
Lits Superposés Futon «Canelle»
Assembly Instructions
Instructions pour l’assemblage
Page 1 of 14 Page 1 de 14
N&D 1018F
Certified:
This bunk bed conforms to all applicable consumer product safety standards
16 CFR PARTS 1213, 1500, 1513 and ASTM F-1427
Replacement Parts:
Replacement parts, including additional guardrails may be obtained from any
Night & Day Furniture Dealer.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
SAFETY WARNING
!
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Prohibit more than one person on upper bunk.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to hooks, belts
and jump ropes.
Keep these instructions for future reference.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress, which is 37 1/2" - 38 1/2" wide and 74"-75" long on upper bunk (twin size.)
Use only mattress, which is 53"-54" wide and 74"-75" long on the lower bunk (full size.)
Ensure that the thickness of the mattress does not exceed 6" and that the mattress surface is
at least 5" (127mm) below upper edge of guardrails.
WARNING:
Adult Assembly Required. This package contains small parts. Keep away from children.
TM
The warning label on your bunk bed headboard is
there by law, and by law is not to be removed. The
adhesive used is difficult to peel off, will tear the paper
leaving a residue that is difficult to clean. We
recommend that you leave it where it is.
Note about Warning Labeling

Night & Day Furniture Cinnamon Futon Bunk Bed Specifications

General

Product Type	Bunk Bed
Material	Wood
Color	Cinnamon
Weight Capacity	400 lbs
Assembly Required	Yes
Dimensions	80" L
Bed Size	Twin

Summary

Safety Warnings and Guidelines

Strangulation Hazard Warning

Warning against attaching items to the bunk bed that could cause strangulation.

Mattress and Foundation Size Requirements

Specifies correct mattress dimensions and thickness for safe bunk bed use.

General Safety Precautions

General safety advice for bunk bed usage, including age limits and maintenance.

Component Identification

Parts by Box (1 & 2)

Identifies components from Box 1 (Head/Footboard) and Box 2 (Decks/Stretchers).

Parts by Box (3 & 4)

Identifies components from Box 3 (Guard Rails/Ladder) and Box 4 (Slats).

Hardware and Tools

Hardware List (Box 1)

Details all hardware included in Box 1 for assembly.

Hardware List (Box 2)

Details all hardware included in Box 2 for assembly.

Required Tools for Assembly

Lists tools needed for assembly, including supplied and not-supplied items.

Lower Frame Assembly

Attaching Lower Stretchers

Instructions for attaching lower stretchers to the lower bunk frame.

Attaching Strong Back to Futon Back Deck

Instructions for attaching the strong back support to the futon back deck.

Futon Back Deck Installation

Positioning Bottom Rollers

Instructions for placing the back deck, ensuring bottom rollers engage correctly.

Engaging Top Rollers

Instructions for lifting the back deck to engage top rollers under the plastic cap.

Lowering the Back Deck

Instructions for lowering the back deck until it lies flat on the frame.

Futon Conversion Steps

Hooking Seat Deck to Snapper

Steps for attaching the seat deck to the rubber snapper mechanism.

Securing Seat Deck to Snap Point

Instructions for pulling the seat over the snap point to secure it.

Converting to Lounge Position

How to push the seat down to achieve the lounge position.

Converting to Sofa Position

How to push the seat with your knee to achieve the sofa position.

Upper Bunk Frame Assembly

Attaching Stretchers and Rear Guard Rail

Instructions for attaching stretchers and the rear guard rail to the upper bunk.

Upper Bunk Guard Rail Installation

Attaching Reversible Guard Rail

Instructions for attaching the reversible guard rail to the upper bunk frame.

Slats Installation

Bolting Slats to Stretchers

Instructions for bolting the initial slats to the stretchers using threaded wood bolts.

Fixing Remaining Slats

Instructions for fixing the remaining slats using wood screws.

Bunk Bed Frame Connection

Connecting Upper and Lower Bunks

Instructions for fitting the upper bunk onto the lower bunk using metal tubes.

Attaching Brackets to Legs

Instructions for fixing the support brackets to the bunk bed legs.

Ladder Assembly and Attachment

Assembling the Ladder

Instructions for assembling the ladder structure using bolts and dowels.

Attaching Ladder to Upper Stretcher

Instructions for fixing the assembled ladder to the upper bunk stretcher.

Futon Seat Disassembly

Lifting Seat from Bed Position

Steps to lift the seat from the bed position, requiring two people.

Removing Seat from Snapper

Instructions for disengaging the seat from the rubber snapper mechanism.

Lifting Seat Clear of Frame

Final step to lift the seat completely clear of the bunk bed frame.

Futon Back Disassembly

Lifting Back Deck Up

Instructions for lifting the back deck upwards, ensuring top rollers clear legs.

Pushing Deck Forward

Steps to push the top of the back deck forward to disengage.

Removing Back from Arms

Final step to lift the back deck away from the bunk bed arms.