NIIMBOT B18 - Page 2

Warning and Attention
Please read these warnings carefully before use to avoid
damage and accidents.
Do not wipe the device with
corrosive chemicals or detergents
Do not operate the device near
any place with flammable
materials such as gas stations
and fuel warehouses
Please keep the device and accessories safe and out of reach of
children to avoid risks.
If any water makes contact with the device, please turn it off immediately.
Please turn off the device immediately in case of any fault in operation.
Do not touch the print head after prolonged and continuous printing to
avoid scalding due to high temperature.
Attention
When the printer is running, do not open the paper bin cover.
When charging, keep the printer and power adapter at room
temperature with good ventilation.
Excessively high or low temperature may damage print quality.
If the printer is stored for a long period of time, please recharge it
every three months.If it is not recharged, the battery may fail or
even leak liquid, damaging the printer.
If the battery fails to meet the performance requirements, please
stop using it immediately and contact the customer service center
for processing.
Please use NIIMBOT label paper to avoid poor printing quality or
even damage to the print head.
In case of any problem during operation, please feel free to contact
the dealer or customer service center. NIIMBOT aims to provide the
best after-sales services for customers all over the world!
1.
2.
3.
4.
5.
6.
7.
Related statements
Quick-Reference Guide
Label Printer
B18
Basic usage
Product name Label Printer
Product size 135*90*37mm
Charging time 3 - 4 hours
Battery capacity 1200mAh
Printing accuracy 203dpi
Product weight
Connection mode
Output power
Bluetooth
Product number NIIMBOT B18
Rated output 5V/1A
Printing mode Thermal transfer
Print width 12mm
Charging method Type-C
Operating temperature 5°C-45°C
308g
-2.782dBm
Product Parameters
Support Email : service@niimbot.com
Official Website : www.niimbot.net
Wuhan Jingchen Intelligent ldentificationTechnology Co., Ltd.
Production Address : No. 1, Tianyang Road, Chuanlong Avenue, Hengdian
Street, Huangpi District, Wuhan City, Hubei Province
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.The device can be
used in portable exposure condition without restriction.
Declaration of conformity
Hereby, Wuhan Jingchen Intelligent Identifification Technology Co., Ltd. declares that this
device is in compliance with the essential requirements and other relevant provisions of Radio
Equipment Directive (RED) 2014/53/EU. This product can be used across EU member states. This
device can be used in European Union.
Hereby, [Wuhan Jingchen Intelligent Identifification Technology Co., Ltd.] declares that the
radio equipment type [NIIMBOT B18] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address:http://www.niimbot.com.
Do not disassemble this
device by yourself
Features Order
On
Off
Print history
Press and hold the "On/Off" button for three seconds
Press and hold the "On/Off" button while power on state
Click the "On/Off" button once while power on state
Self-test page
Double-click the "power button" while power on state
Basic Operation
Indicator
Blue
Blue
Blue
Red
Slow flash
Fast flash
On
Fast flash
On
Slow flash
Status
Standby
Charging
Bluetooth connected
Low battery standby
Description
Indicator
Red
Red
Low battery charging
Low battery bluetooth connected
NIIMBOT is a brand under Wuhan Jingchen Intelligent ldentication Technology Ltd.
© 2022 NIIMBOT. All rights reseed.