Nilfisk-Advance C-PG 130.2 X-TRA Repair Manual

21 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Repair Manual

C 125.4

C 130.2

C-PG 130.2 X-TRA

Table of Contents

Other manuals for Nilfisk-Advance C-PG 130.2 X-TRA

Instructions For Use23 pages

Questions and Answers:

N
Noah MckinneyAug 8, 2025
Why won't my Nilfisk-Advance C-PG 130.2 X-TRA Pressure Washer start?
- J
  Jean LaneAug 8, 2025
  If your Nilfisk-Advance Pressure Washer isn't starting, there are several potential causes. First, ensure the machine is properly plugged in. If it is, try a different socket in case the current one is defective. Also, check the fuse and replace it if it has blown. Finally, if you're using an extension cable, try using the pressure washer without it, as the cable itself may be defective.
J
Jose SuttonAug 13, 2025
What to do if my Nilfisk-Advance C-PG 130.2 X-TRA stops working?
- R
  robert41Aug 14, 2025
  If your Nilfisk-Advance Pressure Washer suddenly stops, several factors could be responsible. Check if the fuse has blown and replace it if necessary. Ensure that the mains voltage matches the specifications on the model tag. If the thermal sensor has activated, allow the washer to cool down for 5 minutes. Lastly, inspect the nozzle for any partial blockages and clean it.
A
anthony99Aug 19, 2025
How to fix fluctuating pressure on my Nilfisk-Advance C-PG 130.2 X-TRA Pressure Washer?
- C
  Cheryl MillsAug 20, 2025
  If you're experiencing fluctuating pressure with your Nilfisk-Advance Pressure Washer, it could be due to a few reasons. One common cause is the pump sucking air; check that all hoses and connections are airtight. Another possibility is that the valves are dirty, worn out, or stuck, in which case you should clean and replace them or refer to local Nilfi sk- distributor. Lastly, worn-out pump seals can also cause this issue; consider cleaning and replacing them or refer to local Nilfi sk- distributor.
T
tayloradamAug 27, 2025
What causes the fuse to blow on my Nilfisk-Advance Pressure Washer?
- R
  Robert TylerAug 27, 2025
  A blown fuse in your Nilfisk-Advance Pressure Washer can occur for a couple of reasons. The fuse might be too small for the machine's amp consumption, in which case you should change to an installation higher than the amp consumption of the machine. Also, you may try without the extension cable.
L
Lisa ShannonSep 1, 2025
Why is my Nilfisk-Advance C-PG 130.2 X-TRA Pressure Washer pulsating?
- J
  Justin WeissSep 1, 2025
  If your Nilfisk-Advance Pressure Washer is pulsating, it could be due to air in the inlet hose or pump. To resolve this, allow the machine to run with the trigger open until regular working pressure resumes. Another cause might be an inadequate supply of mains water. Ensure that the water supply corresponds to the specifications required (see model tag), and avoid using long, thin hoses (min. 1/2).

Nilfisk-Advance C-PG 130.2 X-TRA Specifications

General

Brand	Nilfisk-Advance
Model	C-PG 130.2 X-TRA
Category	Pressure Washer
Language	English

Related product manuals

Preview: Nilfisk-Advance C 120.2

Nilfisk-Advance C 120.2

Preview: Nilfisk-Advance C 120.3

Nilfisk-Advance C 120.3

Preview: Nilfisk-Advance C 100.7

Nilfisk-Advance C 100.7

Preview: Nilfisk-Advance C 135.1

Nilfisk-Advance C 135.1

Nilfisk-Advance C 125.2

Nilfisk-Advance C 125.3

Nilfisk-Advance C 125.7

Nilfisk-Advance C 120.7

Nilfisk-Advance C 110 .7

Nilfisk-Advance C 130.1 X-TRA

Nilfisk-Advance C 120.7 X-TRA

Nilfisk-Advance Nilfisk C 125.3