8.
Remove lid
Press the lid unlock
button and twist
to remove lid.
Use a spoon to create a
1
1
/2-inch wide hole that
reaches the bottom of the
processed ingredients.
Add chopped or broken
mix-ins to the hole. Select
the same processing mode,
then select MIX-IN.
If not adding mix-ins, RE-SPIN
can be used on a crumbly or
powdery output to make it
creamy. RE-SPIN is often
needed for very cold bases.
Do not RE-SPIN before
using MIX-IN program.
Select the mode prior
to selecting RE-SPIN.
OR
9.
2.
Install
Deluxe Pint
Remove lid from Deluxe Pints
and check that ingredients
have not been frozen at an
angle. Place Deluxe Pint with
frozen base in outer bowl.
4.
Install lid
Position tab of lid just
slightly to right of outer
bowl handle so lines
on lid and handle align.
Rotate lid clockwise
to lock.
Assembly & Processing
5.
Install outer bowl
After plugging in unit, place outer
bowl on base with handle centered
on unit. Twist handle to the right to
raise platform and lock bowl in place
(signaled by a click).
1.
Plug in
unit first
Unit will not run
if outer bowl is
installed before unit
is plugged in.
6.
Select processing
mode & program
Press Power. Press a processing
mode (TOP, FULL, or BOTTOM),
then turn dial to select a program
and press dial to begin processing.
7.
Remove bowl
When program is complete, hold
release button on left of motor
base and twist bowl handle
clockwise, then pull away
from unit to remove.
If control panel will not illuminate, ensure unit is properly assembled.
See troubleshooting section of the safety instructions if install light is illuminated.
NOTE
3.
Install
Creamerizer™ Paddle
Press and hold paddle latch
on top of outer bowl lid, then
insert paddle in bottom
of lid. Release latch
to secure paddle.
Disassembly & Cleaning
Remove Deluxe Pint & paddle
Lift pint out of outer bowl.
Rinse outer bowl lid to remove any sticky residue
or pieces wedged in the paddle.
Remove paddle by pressing paddle latch on top of lid.
All parts are top-rack dishwasher safe and can also be hand-washed.
TOP and BOTTOM processing zones are only available with SCOOPABLE programs.
NOTE
OPTIONAL PROCESSING
INGREDIENTS
For Freezing
1
/2 cup fruit punch powdered drink mix
1
3
/4 cup (14 ounces) warm water
Fruit Punch Slushi
Start Here! Prep Your Deluxe Pint Slushi Recipe
*
PREP: 3 minutes | FREEZE: 24 hours | PROGRAM TIME: 5 minutes | MAKES: 2 servings
Place the fruit punch
powder into an empty
CREAMi® Deluxe Pint.
Pour the warm water
into the pint up to the
DRINKABLE FREEZE
FILL line.
Combine mixture until
the drink powder is
completely dissolved.
Place storage lid
on Deluxe Pint and
freeze for 24 hours.
Remove Deluxe Pint
from freezer and
remove lid.
Add pour-in to
DRINKABLE POUR-IN
line. Refer to previous
pages for Assembly &
Processing instructions.
Press FULL, then
use the dial to
select SLUSHI.
When processing
is complete, transfer
slushi to a glass and
serve immediately.
DIRECTIONS
For Freezing
PREFER MORE SIPPABLE? If you prefer a thinner frozen drink after processing, simply add
2–4 additional tablespoons of your desired pour-in, then select RE-SPIN.
NOTE
If your pour-in contains alcohol, select
FROZEN DRINK.
TIP
SCAN HERE
for step-by-step
video to make a
FRUIT PUNCH
SLUSHI
Bowl Release
Button
To remove
outer bowl, hold
release button.
For Processing
Pour-in: water, alcohol, or juice
*Or, turn the page over to prep your
personalized ice cream recipe.
For Processing
ADD 6 oz.
POUR-IN
SLUSHI
PROCESSING MODE
FREEZE
for 24 hours
To Next Page