Nippon Denon AVR-600 User Manual

[7] Last FUNCTION MEMORY
© This receiver is equipped with a fast function memory which stores the input and output setting conditions as they were immediately before the
power is switched off.
This function eliminates the need to perform complicated resettings when the power is switched on.
@ This receive: ts also equipped with a back-up memory. This function provides approximately one week of memory storage with the power cord
disconnected.
TROUBLESHOOTING
tf a problem should arise, first check the following:
1. Are the connections correct?
2. Have you followed ail operational instructions correctly?
3. Are the speakers, turntable, and other components operating properly?
It the receiver is not operating property, check the items listed in the table below Should the problem persist, there may be a malfunction. Disconnect
a ee ee eee
DISPLAY not kt and sound not pro- @ Power cord not plugged in securely. ®@ Check the insertion of the power cord plug.
duced when power switch set to on.
the power unmediately and contact your store of purchase
DISPLAY tt but sound not produced. @ Speaker cords not securely connected. °
© Speaker switch is off.
@ improper position of the audio function but-
ton
@ Volume control set to minimum.
@ MUTING is on
-PROTECT- display appears @ Speaker terminals are short-circuited.
© Block the ventilation holes of the set
© The unit's operating at continuous high pow-
@1 Conditions and/or inadequate ventilation,
‘Sound produced only trom one chan ® Incomplete connection of speaker cords.
nel. © Incomplete connection of input/output
cords.
© Left/right balance is off.
Connect securely.
Turn on speaker switch.
Set to a suitable position.
Turn volume up to suitabie level,
‘Switch off MUTING.
Switch power off, connect speakers proper-
ly, then switch power back on.
Tum off the set's power, then ventilate it well
10 cool it down.
Once the set is cooled down, turn the power
back on.
Turn off the set's power, then ventilate it well
to coot it down.
Once the setis cooled down, turn the power
back on.
* Connect securely.
Connect securely.
Adjust balance knob property.
Common probiems ansing when bsteneng to the CD. records.
tapes, and FM broadcasts, etc
Positions of instruments reversed dur- @ Reverse connections of left and right spesk-
ing stereo playback. os of left and nght input/output cords.
Sound seems distorted. © Rear level is too high
Humiung noe produced when re @ Ground wwe of turntebla not connected
Cord is playing
properly.
@ = lacomplete PHONO jack connection.
@ TV oF radio transmission antenna nearby.
Howling noise produced when volume: @ Turntable and speaker systems [00 clase to-
ws high, gether
@ Floor rs unstable and vibrates easily.
Sound is distorted
‘When playing records
© Stylus pressure 100 weak.
@ Dust os dist on stylus.
@ = Canndge detective
Check left and right connections.
Set the rear level to lower level
Connect securaly.
Connect securely.
Contact your store of purchase.
‘Separate as much as possible.
Use cushions to absorb speaker vibrations
transmitted by floor. If tumtable 1s not
equipped with insulators, use audio insula:
tors {commonly avaiable}.
Apply proper stylus prassura.
Check stylus.
Replace cartridge
Volume 1s weak @ MC cartridge being used
Receiver does nol operate proparly © Battones dead
when remote control unt 1s used @ Remote control unit too far from recewer.
© Obstacle batween receiver and remote con-
trol unit
® Oifferent button is being pressed.
@ = @and O ends of battery inserted in reverse.
Remote contol unit
Replace with MM cartridge or use a head
amplifier or step-up transformer.
Replace with new batteries.
Move closer.
Remove obstacle.
Press the proper button.
Insert bettenes property.
14
[9] SPECIFICATIONS
@ Audio Section
(Power amplifier}
Rated output:
{All properties shown are
only for the power
amplifier stage.)
Output terminals:
(Pre~amplifler)
FRONT {main 2ch driven)
50W + 50W (8 2/ohms, 20 Hz - 20 kHz with 0.08% THD}
CENTER (center Ich driven}
50 W (8 Q/onms, 20 Hz - 20 kHz with 0.08% THD}
REAR (rear 2ch driven)
1SW + ISW (8 Qsohms, 1 kHz with 0.3% THD}
Front: 6 to 16 Q/ohms
Center: B to 16 Q/ohms
Rear: 8 to 16 Q/ohms
Line input {Each line input - FRONT SP OUT)
Input sensitivity / impedance:
Frequency response:
Tone control range:
Signal-to-noise ratio:
150 mV/47 kQ/kohms PHONO (MM): 2 5 mV/47 kQ/kohms
10 Hz to 50 kHz: #308
BASS: +10 dB at 100 Hz
TREBLE: £10 dB at 10 kHz
92 dB (STEREO)
Phono equalizer {PHONO input - REC OUT}
RIAA deviation:
Signal-to—noise ratio:
Rated output / Maximum output:
© Tuner Section
Receiving Range:
Usable Sensitlvity:
50 dB Quieting Sensitivity:
Signal to Noise Ratio (1HF-A):
Tots! Harmonic Distortion
(at 1 kHz):
© Video Section
Standard video jacks
Input and output level /impedance:
Frequency response:
© General
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
@ Remote control unit
System remote contro}
RAC-195:
+ 10B (20 Hz to 20 kHz)
74 dB (A weighting, with 5 mV input)
150 mV /8V
FM] (note: uV at 75 Q/ohms, 0 dBf = 1 x 107'S Wh [AM]
87.5 MHz ~ 107.9 MHz 520 kHz ~ 1710 kHz
1.0 4V 01.2 dBA 18 pV
MONO 1.6 pV (15.3 gBf)
STEREO 23 pV (38.5 dBf)
MONO 8048 50 dB
STEREO 75d8
MONO 0.15%
STEREO 0.3%
1Vp-p/75 Q/ohms
2 Hz to 8 MHz +0, -3dB
AC 120 V, 60 Hz
3.0A
434 (W) x 142 1H) x 315 {D} mm (17-3/32" x §-19/32" x 12-25/64")
7.6 kg (16 tbs 12 02}
Tota! buttons: 28
DENON system code
CD player: 6 buttons
Cassette deck 6 buttons } ISWITCHED)
AVR-600 fixed codes 22 buttons
Batteries: R6P/AA Type (two batteries)
External dimensions: 51 (W) x 175 (H) x 18.5 (DI mm (2” x 6-57/64" x 47/64")
Weight 100 g (Approx. 3 5 02) {including batieries)
* For purposes of improvement, specifications and design are subject to change without notice
15
OOO S/OOS uy mal

Nippon Denon AVR-600 Specifications

General

Brand	Nippon
Model	Denon AVR-600
Category	Stereo Receiver
Language	English