BL-1
BODY, LOCK & SECURITY SYSTEM
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
BL
Revision: October 2006 2006 Maxima
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for work ................................................ 4
PREPARATION ........................................................... 5
Special service tool .................................................. 5
Commercial Service Tool ......................................... 5
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 6
Work Flow ................................................................ 6
CUSTOMER INTERVIEW ..................................... 6
DUPLICATE THE NOISE AND TEST DRIVE ....... 7
CHECK RELATED SERVICE BULLETINS ........... 7
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 7
REPAIR THE CAUSE ........................................... 7
CONFIRM THE REPAIR ....................................... 8
Generic Squeak and Rattle Troubleshooting ........... 8
INSTRUMENT PANEL .......................................... 8
CENTER CONSOLE ............................................. 8
DOORS ................................................................. 8
TRUNK .................................................................. 9
SUNROOF/HEADLINING ..................................... 9
OVERHEAD CONSOLE (FRONT AND REAR) ..... 9
SEATS ................................................................... 9
UNDERHOOD ....................................................... 9
Diagnostic Worksheet ............................................ 10
HOOD ....................................................................... 12
Fitting Adjustment .................................................. 12
FRONT END HEIGHT ADJUSTMENT AND LAT-
ERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT. ................................................................. 12
Removal and Installation of Hood Assembly .......... 13
Removal and Installation of Hood Lock Control ..... 14
REMOVAL ........................................................... 15
INSTALLATION ................................................... 15
Hood Lock Control Inspection ................................ 15
POWER DOOR LOCK SYSTEM .............................. 17
Component Parts and Harness Connector Location ... 17
System Description ................................................ 18
OUTLINE ............................................................. 19
Schematic ............................................................... 20
Wiring Diagram — D/LOCK — ............................... 21
Terminals and Reference Value for BCM ............... 25
Work Flow ............................................................... 25
CONSULT–II Function (BCM) ................................ 26
CONSULT–II BASIC OPERATION PROCE-
DURE .................................................................. 26
DATA MONITOR ................................................. 27
ACTIVE TEST ..................................................... 27
Trouble Diagnoses Symptom Chart ....................... 28
BCM Power Supply and Ground Circuit Check ...... 28
Door Switch Check ................................................. 30
Key Switch and Key Lock Solenoid (Insert) Check ... 32
Door Lock/Unlock Switch Check ............................ 33
Front Door Lock Assembly LH (Actuator) Check .... 35
Door Lock Actuator Check (Front RH and Rear LH/
RH) ......................................................................... 36
Front Door Lock Assembly LH (Key Cylinder Switch)
Check ..................................................................... 37
REMOTE KEYLESS ENTRY SYSTEM ..................... 39
Component Parts and Harness Connector Location ... 39
System Description ................................................. 40
INPUTS ............................................................... 40
OPERATING PROCEDURE ................................ 41
CAN Communication System Description .............. 42
Schematic ............................................................... 43
Wiring Diagram — KEYLES— ................................ 44
Terminals and Reference Value for BCM ............... 47
Terminals and Reference Value for IPDM E/R ....... 47
CONSULT-II Function (BCM) ................................. 48
CONSULT-II Inspection Procedure ......................... 48
“MULTI REMOTE ENT” ....................................... 48
CONSULT-II Application Items ............................... 50
Trouble Diagnosis Procedure ................................. 51
Pre-Diagnosis Inspection ........................................ 52
BCM POWER SUPPLY AND GROUND CIRCUIT
INSPECTION ...................................................... 52
Trouble Diagnoses ................................................. 52
SYMPTOM CHART ............................................. 52
To Next Page
Need help?
General
