Nitecore TINI 2 User Manual

(English) TINI2
Features
Specications
Accessory
Technical Data
Charging Function
Operating Instructions
TINI2
• Multifunctional OLED Real-Time Display
• USB-C Charging
• Advanced Power Cut-Off (APC) Technology
Dual-Core Intelligent
Keychain Light
• Utilizes 2 x OSRAM P8 LEDs with a max output of 500 lumens
• Max peak beam intensity of 2,000cd and max throw of 89 meters
• Utilizesatotalreectiveopticlensforuniformandsoftlight
• MultifunctionalOLEDreal-timedisplayforlumens,batteryvoltageand
runtime etc.
• Built-in 280mAh Li-ion battery
• AdvancedPowerCut-O(APC)technologyforanultra-lowstandbypower
consumption
• Built-inLi-ionbatterychargingcircuitwithaUSB-Cport
•
Highlyecientconstantcurrentcircuitprovidesastableoutputupto60hours
• 2usermodesavailable(DEMOModeandDAILYMode)
• Dualsideswitchdesign
• 5brightnesslevelsavailablewithdirectaccesstoTURBO
• Intelligentmodememoryfunction
• 2lockoutmodesavailable(HalfLockoutModeandFullLockoutMode)
• IncorporatedAdvancedTemperatureRegulation(ATR)module(PatentNo.
ZL201510534543.6)
• Metalringpullabletowithstandupto30kilogramsofweight
• HAIIIhard-anodizednish
• Impactresistantto1meter
Size: 46.6mm×25mm×12.5mm(1.83”×0.98”×0.49”)
Weight: 18.8g (0.66oz)
KeyClasp
FL1
STANDARD
TURBO HIGH MID LOW ULTRALOW
500 Lumens 200 Lumens 65Lumens 15 Lumens 1 Lumen
*15min 45min 2h 30min 8h 60h
89m 56m 32m 14m 6m
2,000cd 800cd 260cd 55cd 9cd
1m(ImpactResistance)
IP54
Note: The stated data is measured in accordance with the international
ashlighttestingstandardsANSI/PLATOFL1-2019,usingthebuilt-inLi-ion
battery (280mAh) under laboratory conditions. The data may vary in real world
use due to dierent battery usage or environmental conditions.
*TheruntimeofTURBOistestedwithoutthetemperatureregulation.
OLED Display
Mode Button
Power Button
Q&A
Q:WhydoesmyTINI2shutdownin30seconds?
A: TINI2 has 2 user modes, DEMO Mode and DAILYMode.Thedefault
settingisDEMOModewheretheproductwillautomaticallyshutdown
if there is no operation in 30 seconds. It is recommended to switch it
to DAILY Mode when in daily use. Please follow the steps below for
mode switching:
1.Whenthelightison/o,longpressboththePowerButtonandthe
ModeButtonsimultaneouslytoswitchbetweenDEMOandDAILY
Mode.
2.TheLEDwillashtoindicatethecurrentusermode:1ashto
indicate DEMO Mode and 2 ashes to indicate DAILY Mode.
Warranty Service
AllNITECORE
®
productsarewarrantedforquality.AnyDOA/defective
product can be exchanged for a replacement through a local distributor/
dealer within 15 days of purchase. After that, all defective / malfunctioning
NITECORE
®
products can be repaired free of charge within 24 months
from the date of purchase. Beyond 24 months, a limited warranty applies,
covering the cost of labor and maintenance, but not the cost of accessories
or replacement parts.
Thewarrantywillbenulliedif
1.heproduct(s)is/arebrokendown,reconstructedand/ormodiedby
unauthorized parties;
2.theproduct(s)is/aredamagedduetoimproperuse.
For the latest information on NITECORE
®
products and services, please
contactalocalNITECORE
®
distributororsendanemailtoservice@
nitecore.com
※Allimages,textsandstatementsspeciedhereinthisusermanualare
for reference purposes only. Should any discrepancy occur between
this manual and information specied on www.nitecore.com, Sysmax
Innovations Co., Ltd. reserves the rights to interpret and amend the
content of this document at any time without prior notice.
Operating Instructions
Multifunctional OLED Display
TINI2isequippedwithamultifunctionalOLEDdisplay.(Pleaseremovethe
screen protector before the rst use.) When the light is turned on, the screen
will successively show the current info (Brightness Level & Lumens, Runtime
Remaining, User Mode) before it goes out. After the screen goes out, short
pressing the Mode Button can reactivate the screen.
Display Demonstration Function
• ThisfunctionisusedfordemonstrationONLY.Itdoesnotreecttheactual
light status.
• Whenthelightiso,pressandholdthepowerbuttonevenafterthe
light accesses ULTRALOW until the light is turned o to enter the display
demonstration.
• In this status, thescreenwillcyclethroughvariousinformationaldisplays.
Short press either button to exit this status.
On / O
On:Whenthelightiso,shortpressthePowerButtontoturniton.
O: When the light is on, short press the Power Button to turn it o.
User Modes
TINI2has2usermodes,DEMOModeandDAILYMode.
DEMO Mode: The light will automatically shut down if there is no operation in
30seconds(reactivatingthescreenexcluded).Thecountdownwillbedisplayed
on the screen.
DAILY Mode: The lightwillnotautomaticallyshutdownandwillneedtobe
shut down manually.
Note: The default setting is DEMOMode.Itisrecommendedtoswitchitto
DAILYModewhenindailyuse.
Mode Switching
Whenthelightison/o,longpressboththePowerButtonandtheModeButton
simultaneously to switch between DEMO and DAILY Mode.
The LED will ash to indicate the current user mode: 1 ashtoindicateDEMO
Mode and 2 ashes to indicate DAILY Mode.
(In this process, the screen will show “DEMO”or“DAILY”toindicatethecurrent
user mode.)
Note: Reactivating the light within 3 seconds after it automatically shutsdown
inDEMOmodewilltemporarilyaccessDAILYModeuntilitisturnedo.
Brightness Levels
Whenthelightandthescreenison,shortpresstheModeButtontocycle
through “ULTRALOW – LOW – MID - HIGH”. The ashlight will directly access
the previously memorized brightness level when reactivated.
Note: When the screen is o, short press the Mode Button toactivatethe
screenbeforeadjustingthebrightnesslevel.
Direct Access to ULTRALOW
Whenthelightiso,longpressthePowerButtontodirectlyaccessULTRALOW.
Direct Access to TURBO
Whenthelightison/o,pressandholdtheModeButtontoaccessTURBO.
Release to return to previous status.
Lockout / Unlock
TINI2hastwolockoutmodes(HalfLockoutModeandFullLockoutMode).
Half Lockout Mode (Lockout 1):
• Whenthelightison,pressandholdthePowerButtonuntilthescreenshows
the Lockout 1 icon to access Half Lockout Mode.
• When in Half Lockout Mode, the Power Button is unavailabletoactivatethe
ashlight. Holding the Mode Button is still available for accessing TURBO.
Full Lockout Mode (Lockout 2):
• Whenthelightison,pressandholdthePowerButtonevenafteraccessing
HalfLockoutMode,untilthescreenshowsLockout2icontoaccessFull
Lockout Mode.
• WheninFullLockoutMode,bothbuttonsareunavailabletoactivatethe
ashlight.
Unlock:
• IneitherLockoutMode,shortpressandthenlongpressthePowerButton,
during which the screen will show an unlock icon and a progress bar, until
the ashlight is activated to exit Lockout Mode. The light will access the
previous memorized level.
• The light will be automaticallyunlockedwhenbeingrechargedineither
Lockout Mode.
ATR (Advanced Temperature Regulation)
TheintegratedATRtechnologyregulatestheoutputoftheTINI2according
to the working condition and ambient environment to maintain the optimal
performance.
Power Indication
Whenthelightiso,shortpresstheModeButtontodisplaythebatterylevel,
the battery voltage, the memorized brightness level and the current user mode
before it goes out. Dierent voltages represent the corresponding remaining
battery power levels:
Note: When the battery voltage is below 3.4V, the power indicator beneath
bothbuttonswillashblueevery2secondstoinformtheusertorechargethe
battery as soon as possible.
Charging Function
TINI2isequippedwithanintelligentchargingsystem.Pleasechargethebattery
before the rst use.
Connecting to the External Power: As illustrated, use the USB cable to
connectanexternalpowersupply(e.g.aUSBadapter,acomputerorotherUSB
charging devices) to the USB port to begin the charging process. The charging
time is approx. 1 hour 45 minutes.
Charging Indicator: When the charging status is normal, the charging
indicatorwillashslowlytoinformtheuserandthescreenwillshowthe
current battery level. When the battery is fully charged, the charging indicator
will become steadily turned on to inform the user and the screen will display a
full battery level.
Cautions
1.TheTURBOBrightnessLevelof500lumenswillproducemassiveheat
rapidly during long-time activation. Use caution when operating the lightin
TURBO mode to avoid overheating and step down to a lower level if the light
becomes too hot to handle.
2.CAUTION!Possibledangerousradiation!Don'tlookintothelight!Maybe
dangerous for your eyes.
3.Pleaserechargetheproductevery3monthswhenleftunusedfora
prolonged time.
4.Theproductcontainssmallassemblyparts.Pleasekeepitawayfromchildren
to avoid danger of choking or suocation.
5.Whentheashlightiskeptinthebackpack,pleaseactivatetheLockoutMode
to prevent accidental activation.
6.DONOTdisassemble,modifyorreconstructtheproduct,otherwisethe
warranty will be nullied, and the product might be damaged.
（Half Lockout Mode）
（Full Lockout Mode）
Low power Full power
3.5V 3.7V 3.9V 4.2V
SYSMAX Innovations Co., Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address： Rm2601-06,CentralTower,
No.5XiancunRoad,TianheDistrict,
Guangzhou,510623,Guangdong,China
Please 󽗉nd us on facebook : NITECORE Flashlight
Thanks for purchasing NITECORE!
TINI0601221
MadeinChina

Nitecore TINI 2 Specifications

General

Max Output	500 lumens
Max Beam Intensity	2000 cd
Battery Capacity	280mAh
Runtime	Up to 60 hours
Water Resistance	IP54
Impact Resistance	1 meter
Beam color	White light
Charging	USB-C
Material	Aluminum alloy
Beam Distance	89 meters
Battery	Li-ion
Weight	18.8g
Special Modes	Beacon
Feature	Rechargeable
Modes	Turbo, High, Low, Ultralow