What to do if displays and indicators are off, but a continuous audible alarm is sounding on Nonin PalmSAT 2500A VET?
If the displays and indicators are off, but a continuous audible alarm is sounding, this indicates a system fault. Turn the device off and on. If the problem persists or the device does not turn on, replace or recharge the batteries. If the problem continues, contact Nonin Technical Service.
Why am I experiencing disruption in the Nonin PalmSAT 2500A VET Pet Care Product performance?
Disruption in device performance may be due to electromagnetic interference (EMI). Remove the device from the EMI environment.
General| Category | Pet Care Product |
|---|---|
| Model | PalmSAT 2500A VET |
| Brand | Nonin |
| Display | LED |
| Measurement Parameters | SpO2, Pulse Rate, Perfusion Index |
| Battery Type | AA alkaline or rechargeable |
| SpO2 Range | 0 – 100% |
| Storage Temperature | -40° to +70°C |
| Humidity | 10 – 95% noncondensing |
| Compatible Sensors | Nonin sensors |
| Accuracy SpO2 | ±2% (70% to 100%) |
| Operating Temperature | 32°F to 122°F (0°C to 50°C) |
Prohibits use in explosive or flammable atmospheres, including anesthetics or gasses.
Warnings for MR environments, defibrillation, ESU interference, cable routing, and alarm silence.
Warnings on sensor site care, alarm settings, modifications, battery status, and speaker obstruction.
Investigate sensor dislodgement alarms. Normal values may display under certain conditions.
Not an apnea monitor. Verify startup. Minimize motion artifact. Perfusion issues affect accuracy.
Clean with specified agents. Use Nonin batteries. Do not mix charge states. Dispose properly.
Storage guidelines, EMC compliance, WEEE directive, and RF interference concerns.
Factors affecting accuracy, repair policy, sensor compatibility, and pharmacological effects.
Proper sensor placement, perfusion, and data coupling reliability.
Explains symbols for caution, instructions, CE marking, UL/CSA certification, and serial number.
Describes symbols for WEEE, Authorized Representative, Manufacturer, and Country of Manufacture.
Explains symbols for storage temperature range and RoHS compliance.
Defines symbols for %SpO2, Pulse Rate, Pulse Quality LED, Low Battery LED, Alarm Silence LED, On/Off, and Advance buttons.
Describes the 3-digit LED displays for SpO2 and pulse rate, including error indications.
Identifies the Pulse Oximeter Sensor Connector, Speaker, Advance Button, and On/Off Button.
Tricolor LED indicating pulse strength (green, amber, red) and pulse detection.
Amber LED for low battery (medium alarm) and blinking amber for alarm silence.
Bicolor LED indicating alarm priority: amber for medium, red for high.
Pulse rate tone beeps with SpO2 values. Audible alarms for high/medium priority.
Turns the device on/off. Selects values and advances settings in Setup mode.
Adjusts volume/reviews settings in normal operation. Scrolls values in Setup mode.
Handheld pulse oximeter for animals, displays SpO2/pulse rate, provides audible/visual alarms.
Measures SpO2 by light absorption through perfused tissue, detecting pulse variations.
Tricolor LED for pulse quality. Sensor disconnect/malfunction indicated by red blink/dash.
Requires no calibration. Operates 60 hrs on alkaline, 40 hrs on NiMH battery pack.
Uses AA alkaline or NiMH pack. Lists operating life for each type.
Details storage life for alkaline and NiMH batteries based on calendar/clock setting.
Recharge time for NiMH pack. Device turns off at critically low battery capacity.
Step-by-step guide to replacing batteries, emphasizing safety precautions.
Details battery life, storage, and recharging considerations for alkaline and NiMH batteries.
Connect sensor with Nonin logo facing up. Refer to Sensor Placement for details.
Press On/Off to turn on; press and hold to turn off. Auto power-off after 10 min inactivity.
Describes the startup sequence: display checks, indicator flashes, and revision number display.
Verify sensor position, pulse quality, and stable readings. Reposition/replace if indicators are red/amber.
Lists sensor types (Lingual Clip, Flex, Transflectance) and cleaning instructions.
Use Nonin sensors only. Oximeter calibrated for human hemoglobin; animal calibration may vary.
Lists factors degrading performance: light, motion, ESU, flow restrictors, moisture, sensor issues.
Check sensor sites periodically. Shave site for Flex/Transflectance sensors.
Recommended site is the tongue. Ensure full clip placement for accurate SpO2.
Inadequate perfusion or poor sensor application causes erratic readings. Remove if operation not verified.
Use on toe or tail base. Shave site, position correctly, and secure with tape.
Use on tail base (anal orifice). Shave site, position correctly, and secure with tape.
Controls are On/Off and Advance buttons. Setup mode for alarms, memory, and clock.
Procedure to enter Setup mode using On/Off and Advance buttons by holding them in sequence.
Steps to change settings, skip, store values, and advance to the next setting.
Covers Pulse Rate Low/High Alarms and SpO2 High Alarm settings with adjustable ranges.
Adjustable audible alarm levels and options for Memory Clear/Delete.
Settings for Year, Month, Day, Hour, and Minute for the device's clock.
Details default and adjustable options for SpO2/Pulse Rate alarms and alarm volume.
Procedure to recall previous alarm and volume settings using Setup mode.
How to review current alarm limits and volume settings during normal operation.
Temporarily silence alarms for 2 minutes. Alarm Silence indicator blinks.
Function to delete stored data. Confirmation prompts for clearing memory.
Procedure to set the device's year, month, day, hour, and minute.
Wipe with damp cloth and mild detergent/bleach. Avoid specific agents and liquid immersion.
Clean devices and sensors separately. Use OxitestPlus7 to verify operation.
The device features audible and visual alarms for high and medium priority conditions.
Animal-specific alarms indicated by red Alarm Bar and audible tones (3 beeps, pause, 2 beeps).
Equipment-specific alarms indicated by amber Alarm Bar and audible tones (3 beeps, 25-sec pause).
Details conditions for medium priority alarms: inadequate signal, sensor fault, data not updated, battery low/critical.
Error messages (e.g., Err E01) or continuous audible alarm indicate system fault.
Stores up to 72 hours of SpO2/pulse rate data. Overwrites oldest data. Samples every 4 seconds.
Connect to computer, enter Setup mode, and data plays back automatically.
Provides real-time data output via the pulse oximeter sensor connector.
Details pin assignments for the 9-pin Sub-D connector for serial data output.
ASCII serial format at 9600 baud, 9 data bits. SPO2=XXX HR=YYY format.
Integrator must analyze risks. Changes require additional analysis. Verify equipment suitability.
Device requires trained personnel repair. Do not open case. No periodic maintenance needed.
Provides contact details for Nonin Medical Inc. and Nonin Medical B.V. for technical assistance.
3-year warranty on device, excludes sensors/cables/batteries. Details repair/replacement policy.
Lists rechargeable NiMH battery pack and charger stand.
Includes power cords, carrying case, and operator's manuals.
Lists available reusable sensors: Small Lingual Clip, Small Animal Flex, Transflectance.
Lists extension cables, memory cable, and real-time cable.
Using non-specified accessories may affect emission and immunity. Use only Nonin-branded sensors.
Addresses issues like depleted batteries, incorrect installation, sensor faults, or no signal.
Correlates pulse rates with ECG, addresses ESU interference, and marginal pulse quality.
Covers low pulse strength, poor perfusion, incorrect positioning, and excessive light/motion.
Addresses red indicator, dashes, missing segments, system faults, and EMI.
Product complies with ISO 10993-1. Functional tester cannot assess accuracy.
Serial port accessories must be certified per IEC/UL standards for data-processing equipment.
Portable and mobile RF communications equipment can affect medical electrical equipment.
Device emits low RF energy (Group 1) and is suitable for domestic establishments (Class B).
Details compliance levels for ESD, Fast Transient/Burst, Surge, Voltage variations, and Magnetic Field.
Provides separation distances for RF equipment based on power and frequency.
Table detailing separation distances between RF transmitters and the device.
Specifies response and latency for SpO2, Pulse Rate, and equipment delays.
Describes SpO2 accuracy testing on human subjects under induced hypoxia.
Details tests for pulse rate accuracy with motion and performance at low perfusion.
Explains how pulse oximetry works by measuring light absorption differences.
Lists SpO2/Pulse Rate ranges, accuracy, alarm volumes, wavelengths, indicators, temperature, humidity, altitude.
Provides physical dimensions, weight, protection types (BF, IP32), and mode of operation.
To Next Page