A
Alexander YatesAug 17, 2025
Why does my Normstahl Garage Door Opener have interference frequencies?
- NNicole JonesAug 17, 2025
The wireless signals of other 433 MHz transmitters can interfere with the Normstahl garage door opener.
To Next PageTo Next PageWhy does my Normstahl Garage Door Opener have interference frequencies?
The wireless signals of other 433 MHz transmitters can interfere with the Normstahl garage door opener.
What to do if Normstahl Magic 1000 has a persistent error after two successive self-tests?
If the same error occurs in two successive self-tests, the control system will be disabled, and commands will be rejected. After about one minute, the system runs another self-test. If no errors are detected, the control system is enabled again. If the error persists, a reset will need to be performed. This deletes all settings, and the door operator will have to be taught in again.
What does error 002 mean on a Normstahl Magic 1000 Garage Door Opener?
The error code 002 indicates EEprom data.
What does error 003 mean on a Normstahl Magic 1000 Garage Door Opener?
The error code 003 indicates current measurement.
What does error 004 mean on a Normstahl Magic 1000?
The error code 004 indicates a hardware photo cell issue.
What does error 005 mean on a Normstahl Magic 1000 Garage Door Opener?
The error code 005 means switch off thyristors.
What does error 006 mean on a Normstahl Magic 1000?
The error code 006 means switch off relay.
What does error 007 mean on a Normstahl Garage Door Opener?
The error code 007 indicates a watchdog test issue.
What does error 008 mean on a Normstahl Magic 1000?
The error code 008 indicates a ROM test issue.
What does error 009 mean on a Normstahl Magic 1000 Garage Door Opener?
The error code 009 indicates a RAM test issue.
The door operator may only be used if the entire range of motion is clearly visible. Be mindful of others.
Automatic load switch-off prevents accidents due to moving door. Check by stopping door with hands.
Check emergency release as per information on page 168 (J).
Check for proper functioning of additional safety devices as per manufacturer's instructions.
Describes status messages (A, B, C) and function codes (L4, L3, L2, L1, Err) of the indicator lamp.
Procedure to teach the door operator end positions and load values using a remote transmitter.
Procedure to teach the door operator end positions and load values without a remote transmitter.
Enters the programming mode to adjust settings via the menu by pressing the Menu button.
Navigates through different programming menus using the ↑ and ↓ pushbuttons.
Displays current settings and allows modification using the ↑ and ↓ pushbuttons.
Exits the programming mode, saving any changes made by pressing the Menu button.
Connects a photo cell for safety during door operation. Stops and reverses door on obstruction.
Connects an emergency stop button. Stops the door immediately when activated.
Details on connecting safety rails, opto-sensors, and warning lights via extension modules.
Optional connection for additional lighting, performed by qualified electricians.
Allows connection of an external pulse signal, like a wall button.
Describes how other 433 MHz transmitters can interfere with the operator's wireless signals.
Explains the self-test function and lists common error messages and their meanings.
Provides remedies for common issues like error messages, light flashes, and system non-responsiveness.
Checking radio signal strength and connecting an external antenna for improved reception.
Guidance on replacing fuses and remote transmitter batteries.
General| Manufacturer | Normstahl |
|---|---|
| Max. pulling force | 1000 N |
| Opening speed | 0.2 m/s |
| Motor Type | DC |
| Speed | 0.2 m/s |
| Voltage | 230 V |
| Safety Features | Obstacle detection |
| Remote Control | Yes |
