Norton 6900 PowerMatic

To Next Page

Standard Duty Double Lever Arm Application for Frame Reveals to 6-7/8” (175mm)

Stop (Push) Side of Door Installation For Handed (Not Reversible) Units

Door Openings 85° to 110° Use Series 6920 / 6921

Door Openings 111° to 180° Use Series 6930 / 6931

80-9369-0120-020 (09-08 )

Right Hand DoorLeft Hand Door

80-9369-0120-020 (09-08)

WARNING

120 VOLT POTENTIAL PRESENT. MAKE SURE

POWER IS TURNED OFF DURING

INSTALLATION PROCEDURE.

An incorrectly installed or improperly

adjusted door operator can cause property

damage or personal injury. These

instructions should be followed to avoid the

possibility of misapplication or

misadjustment.

CAUTION

AmericansWithDisabilitiesAct(A.D.A.)

ANSIStandards

ANSI A117.1

providing

accessibility and usability for physically

handicappedpeople"

• ANSI A156.19

"for power assist and low energy power

operateddoors"

U.L.Listing

Underwriters Laboratories,Inc. listed for use on

fire and smoke barrier door assemblies when the

120VAC (60Hz) power input is supplied through

the normally closed alarm contacts of a

compatible U.L. Listed alarm system or alarm

panel.

These door operators can be installed and adjusted to conform with

A.D.A.regulations.

– These door operators permit door

assemblies to conform to the requirements of this

specification "for buildings and facilities –

– These products are designed to conform to this

specification

– "PAS" Function is designed to meet or exceed all of the

requirementsforthe"PowerAssistDoor".

– "POR" Function is designed to meet or exceed all of the

requirementsforthe"LowEnergy PowerOperated Door".

CUS

6900 PowerMatic

Low Energy Power Operator

Installation Instructions

ActivationModes (Modes are configured during installation.)

• Selectively Activated Mode -

• Automatically Activated Mode -

Functions(Functionsareconfiguredduringinstallation.)

• Power Assist function (PAS)

unit depends upon external

switchesorscannersforactivationoffunctions.

unit will operate

utilizing on-board

ELS switchingthat automatically activatesthe functions. External

switchesorscannersmayalsobeusedforactivation.

– The unit operates as a standard

door closer unless activated via one of the Modes listed above.

Upon activation the door opening resistance is reduced, for a

selected period of time, well below A.D.A. guidelines. When the

time period expires, the door closes under normal door closer

spring power.

with a slight

movement of the door toward the open position

– The unit performs as a low

energy power door operator. Field settings allow for following two

functions:

1.SelectivelyActivatedMode(SeeAbove).

2.AutomaticallyActivatedMode(SeeAbove).

• Power Operator function (POR)

NOTE: The are factory set in the

asa

ELS Board Dip Switches

SelectivelyActivatedMode PowerOperatorFunction.

Basic Requirements

Parts Identification

Installation Template

Installation Sequence

Regulation & Adjustment

General Product Information

Function and Operation Sequence

ELS “Timing” Calibration

ELS Reset Instructions

Troubleshooting

Need help?

Do you have a question about the Norton 6900 PowerMatic and is the answer not in the manual?

Summary

Activation Modes

Selectively Activated Mode

Unit depends upon external switches or scanners for activation of functions.

Automatically Activated Mode

Unit operates with slight door movement utilizing on-board ELS switching.

Functions

Power Operator Function (POR)

The unit performs as a low energy power door operator.

Power Assist Function (PAS)

Unit operates as a standard door closer unless activated.

Americans With Disabilities Act (A.D.A.)

ANSI Standards

Operators conform to A.D.A. and ANSI A117.1/A156.19 specifications for accessibility.

U.L. Listing

Determine Hand of Door

General Frame and Door Preparation

Verify frame reinforcement, anchoring, and prepare for conduit and wires.

Fasteners for Frame

Lists required screws for frame mounting (hollow metal/aluminum).

Fasteners for Door

Lists required screws and sex nuts for door mounting.

Installation Sequence

Frame and Door Hole Preparation

Details drilling frame holes for conduit and preparing door holes for sex nuts.

Arm Installation

Guides on aligning and securing the main arm onto the pinion shaft.

Teaching Closed and Open Door Positions

Obstruction Operation

Details how the unit responds to obstructions during opening or closing.

Obstruction Sensitivity

Adjusting delay for obstructions via dip switches T1 and T2.

Adjustments for the PowerMatic Product

Mechanical Adjustment

Setting closing power using the Power Adjustment Nut.

Hydraulic Adjustment

Adjusting sweep, latch, and backcheck valves for speed and cushioning.

Electrical Adjustments

Setting selector mode switch and CL/AS DLY timer for functions.

General Product Information

Selector Mode Switch

Three-position switch (OFF, ON, H/O) for unit operation control.

SC Speed Control Valve

Adjusts door opening speed (POR) or force (PAS).

PA Pressure Adjustment Valve

Factory set adjustment for opening force, usually not requiring adjustment.

Function and Operation Sequence

Vestibule Operation

Allows delayed initiation of a power cycle from a remote location.

Power Operator Function (POR)

Operator fully opens door, sustains, then releases and closes.

Power Assist Function (PAS)

Requires minimal force to open/close, sustained for duration.

ELS Board Timing Instructions

RH-PUSH Units Calibration

Procedure to calibrate the ELS board for right-hand push units.

LH-PUSH Units Calibration

Procedure to calibrate the ELS board for left-hand push units.

ELS Reset Instructions

Resetting of ELS Board

Steps to reset the ELS board and re-teach door positions.

Troubleshooting

Door Closing Force Issues

Addresses insufficient closing force and speed regulation.

Door Opening Force;Speed Issues

Addresses opening force too strong or opening too fast.

Door Not Opening Far Enough

Solutions for doors not opening to the full position.

Motor Shuts Off; Obstruction Sensing

Troubleshooting motor shut-off due to sensed obstructions.

No Power; LED Issues

Diagnosing issues related to no power or LED indicators.