Nouvag MD 30 - User Manual

Questions and Answers

K
kevinponceAug 13, 2025
Why is there no irrigation fluid for the instrument in my Nouvag Laboratory Equipment?
- S
  stephanie59Aug 13, 2025
  If there's no irrigation fluid for the instrument in your Nouvag Laboratory Equipment, consider the following: * Ensure the peristaltic pump is switched on. * Check that the tubing set is correctly inserted, paying attention to the direction. * Replace the tubing set if it's clogged or shows crusted matter. * Open the ventilation filter at the drip chamber if the bottle with sodium chloride solution isn't ventilated. * Replace the tubing set if it is dripping. * Ensure the roller clamp of the tubing set is fully open.
S
stephen64Aug 17, 2025
What to do if the motor does not run on my Nouvag MD 30?
- J
  Julie SantosAug 17, 2025
  If the motor isn't running on your Nouvag Laboratory Equipment, try these steps: 1. Switch on the motor using the treadplate. 2. If you're using a Vario pedal, try switching to the other motor. 3. Ensure the motor cable is securely connected to the control unit. 4. Check that the handpiece or contra angle is correctly assembled by firmly pressing it onto the electronic motor until it clicks and is secure.
D
Dylan HarveyAug 21, 2025
How to troubleshoot a non-operational pedal on Nouvag MD 30?
- J
  John Shaw MDAug 21, 2025
  If the pedal isn't working with your Nouvag Laboratory Equipment: * Make sure the pedal is correctly connected to the control unit. * Review the operating instructions to ensure correct operation.
K
Kevin HallAug 25, 2025
What to do if my Nouvag Medical Equipment device is not operational?
- E
  Elizabeth StrongAug 26, 2025
  If your Nouvag Medical Equipment device isn't working, there are several potential causes: * The control unit may not be switched on. Ensure the power switch “I/O” is set to “I”. * The power connection might not be established. Connect the control unit to the mains power supply. * The operating voltage could be incorrect. Check the mains voltage. * There may be a faulty fuse. Replace the fuse. * A processor error might have occurred. Switch the main switch “I/O” to position “I”, wait 10 seconds, and then switch it back to position “O”.
C
Charles CarrollAug 29, 2025
Why is there no irrigation fluid for my Nouvag Medical Equipment instrument?
- J
  John HollowayAug 29, 2025
  If you're experiencing a lack of irrigation fluid in your Nouvag Medical Equipment, consider the following: * The peristaltic pump may not be switched on. Switch it on. * The tubing set may be incorrectly inserted. Ensure it's correctly inserted, noting the direction. * The tubing set could be clogged or have visible crusted matter. Replace the tubing set. * The bottle with sodium chloride solution might not be ventilated. Open the ventilation filter at the drip chamber. * The tubing set may be dripping. Replace it. * The roller clamp of the tubing set might be closed. Open the roller clamp all the way. * A non-conforming tube set may be in use (not from Nouvag or the wrong type). Use the tube set recommended by Nouvag.
M
michele34Sep 1, 2025
What to do if the motor does not run on my Nouvag Medical Equipment?
- M
  Michelle WallaceSep 1, 2025
  If the motor on your Nouvag Medical Equipment isn't running, check these potential causes: * The motor might not be switched on. Switch on the motor using the treadplate. * The incorrect motor may be active. Switch to the other motor using the VARIO pedal. * The motor might not be connected. Connect the motor cable to the control unit. * The handpiece or contra angle might not be correctly assembled. Press the handpiece firmly onto the electronic motor until it clicks into position and ensure it is secure by moving it slightly in the opposite direction.
F
fcombsSep 5, 2025
What to do if I see a red display illumination on my Nouvag Medical Equipment?
- T
  Tina JohnsonSep 5, 2025
  If you notice a red display illumination on your Nouvag Medical Equipment, it could indicate one of the following issues: * The motor might be missing. Connect the motor. * There could be a motor fault, or the motor cable is broken. Check the motor and its cable. * The AS limit may have been reached with an instrument. Release the pedal and press it again.
C
Cheryl PetersonSep 8, 2025
What to do if the pedal is not operational on my Nouvag Medical Equipment?
- T
  Timothy VaughnSep 8, 2025
  If the pedal on your Nouvag Medical Equipment isn't working, consider these possibilities: * The pedal might not be connected. Connect the pedal to the control unit. * The operation might be incorrect. Check the operating instructions.