10. Attach Rower Cross Bar
The Rower Cross Bar should be a straight bar connecting both Side Rails.
a. Place the Rower Cross Bar on top of the Side Rails approximately
34” back from the Foot Bar.
i. Assemble the Rower Seat Cross Bar on top of the Side Rails
with the U-Bolts on the underneath side of the rail and the
threads running through the (2) LoPro holes.
ii. Place washers on threaded ends of the U-Bolts and loosely
tighten nuts onto the LoPros with a 1/2” socket wrench. Do NOT
completely tighten.
11. Attach Back Rail - Right
a. Run the anchor line at the back end of the Side Rail – Right
through a Frame Coupler.
b. Continue running the anchor line through the front end of the Back
Rail and out the slot at the back end of the rail.
c. Loosen the bolts on the Frame Coupler and slip it onto the back
end of the Side Rail – Right with the bolt heads facing up and on
the outside of the Side Rail.
i. Use the slotted window in the Frame Coupler to position the
Side Rail in the middle of the Frame Coupler.
d. Slip the Back Rail into the Frame Coupler on the Side Rail –
Right.
i. Orient the Back Rail so the bend follows the raft tube and the
back anchor mast extends horizontally o the back center of
the raft.
ii. Use the slotted window in the Frame Coupler to position the
Back Rail in the middle of the Frame Coupler.
1. The ends of the Side Rail and Back Rail should touch and be
visible in the slotted window of the Frame Coupler.
2. Tighten down the Frame Coupler bolts with a 1/2” socket
wrench to keep the Back Rail in position.
Do NOT completely tighten.
12. Attach Back Pulley Bracket
a. Slip the anchor Pulley Bracket over the back end of the Back Rail
– Right and slide down until centered with the slot.
b. Assemble the Pulley Wheel onto the anchor Pulley Bracket and
securely tighten down the bolt with an Allen wrench.
i. The anchor line should be running over and around the pulley
wheel on the Pulley Bracket.
13. Attach Back Rail – Left
a. Loosen the bolts on the Frame Coupler and slip it into the back
end of the Side Rail – Left with the bolt heads facing up and on
the outside of the Side Rail.
i. Use the slotted window in the Frame Coupler to position the
Side Rail in the middle of the Frame Coupler.
b. Slip the Back Rail into the Frame Coupler on the Side Rail – Left.
i. Orient the Back Rail so the bend follows the raft tube.
ii. Use the slotted window in the Frame Coupler to position the
Back Rail in the middle of the Frame Coupler.
1. The ends of the Side Rail and Back Rail should touch and be
visible in the slotted window of the Frame Coupler.
2. Tighten down the Frame Coupler bolts with a 1/2” socket
wrench to keep the Back Rail in position.
Do NOT completely tighten.
14. Attach Back Angler Seat Bar
a. Place the Back Angler Seat Bar on top of the Back Rails centered
and angled upward.
i. Assemble the Angler Seat Bar on top of the Side Rails with the
U-Bolts on the underneath side of the rail and the threads
running through the (2) LoPro holes.
ii. Place washers on threaded ends of the U-Bolts and loosely
tighten nuts onto the LoPros with a 1/2” socket wrench. Do NOT
completely tighten.
15. Attach Back Thigh Hook Bar
a. Place the Back Thigh Hook Bar on top of the Side Rails
approximately 12” to 16” back from the Rower Cross Bar.
i. Assemble the Thigh Hook Bar on top of the Side Rails with the
U-Bolts on the underneath side of the rail and the threads
running through the (2) LoPro holes.
ii. Place washers on threaded ends of the U-Bolts and loosely
tighten nuts onto the LoPros with a 1/2” socket wrench. Do NOT
completely tighten.
16. Attach Back Angler Thigh Hook
a. Place the open pipe ends of the (2) bent frame pipe sections into
the slots on the bottom of the Angler Thigh Hook.
i. Use the (2) lock pins to secure the bent frame pipe to the
Angler Thigh Hook.
b. Use (2) U-Bolts to secure the (2) LoPros on the bent pipe sections
attached to the Angler Thigh Hook to the Thigh Hook cross bar
pipe.
i. Center the Angler Thigh Hook in the middle of the boat and
Thigh Hook cross bar.
ii. Assemble the Angler Thigh Hook with the U-Bolts on the front
straight frame pipe section.
iii. Place washers on threaded ends of the U-Bolts and loosely
tighten nuts onto the LoPros with a 1/2” socket wrench. Do NOT
completely tighten.
1. Rotate the Angler Thigh Hook until it is at the desired height
and angle.
iv. Firmly tighten the LoPro nuts with a 1/2” socket wrench to
secure the Angler Thigh Hook.
17. Firmly tighten bolts on LoPro fittings and Frame Couplers with a
1/2” socket wrench
a. Firmly tighten the LoPro nuts on the Front Angler Seat Bar.
b. Firmly tighten the bolts on the front (3) Frame Couplers connecting
the Side Rails and Front Rails.
c. Firmly tighten the LoPro nuts on the Foot Bar.
d. Firmly tighten the LoPro nuts on the Rower Seat Cross Bar.
e. Firmly tighten the LoPro nuts on the Back Thigh Hook Bar.
f. Firmly tighten the bolts on the back (2) Frame Couplers connecting
the Side Rails and Back Rails.
g. Firmly tighten the LoPro nuts on the Back Angler Seat Bar.
18. Attach Oar Mounts
a. Attach the Oar Mounts on top of each of the (2) Side Rails
approximately 12“ to 16” in front of the Rower Seat Cross Bar. The
exact position is dependent on the rower’s arm length.
b. The U-Bolts will secure around the rails from the bottom side of
the rail with the threads running through the (2) Oar Mount holes.
c. Place washers on threaded ends of the U-Bolts and loosely tighten
nuts onto the LoPros with a 1/2” socket wrench.
Do NOT completely tighten.
d. Rotate the Oar Mount so the top (area with oar lock mount hole)
To Next Page
Loading...