NuTone la600wh

1
LA600WH WIRED /
WIRELESS DOOR CHIME
To register this product, visit: www.nutone.com
THIS PACKAGE INCLUDES:
n Wired / Wireless Door Chime with MP3 upload capability
n Decorative White Chime Cover
n USB Cable
n Mounting Hardware
n Pushbutton Diode (required for wired installation)
Door chime comes with eight pre-loaded sounds. Prior to installation,
upload desired MP3 sound files.
1. Remove chime cover (B) from chime base (A). You may need to
insert a finger into the large hole on the back of the chime base.
(Figure 1)
UPLOAD MP3 TUNES
1. Insert a USB Mini cable end into the doorbell mechanism USB jack
(C). (Figure 1)
2. Insert the remaining larger USB cable end into a USB port on your
computer.
3. On your WINDOWS computer,
• Select“Start”inthebottomcornerofyourDesktop.
• Select“MyComputer”
• Selectthenewdevicedetected.(Thedrive“D:”,“E:”,etc.willvary
from computer to computer).
• Selectthedevice.
• Youwillnowseeawindowthatcontainsseveralmp3files.These
are the tunes that are pre-installed on your doorbell mechanism.
• Searchyourcomputerforothermp3songsthatyouwishtoplay
onyourdoorbellmechanismwhenactivated.Note:Filesmustbe
in mp3 format.
• Onceyouhavelocatedthosefiles,simply“COPY”thefileand
“PASTE”itintothefolderthatcontainsthepre-installeddoorbell
files.
• Confirmthatthetransferedfilesarecomplete.
4. Remove USB cable and proceed to one of the following sections.
INSTALLATION & OPERATING INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WIRES
TO
CHIME
SUPPLY
WIRE
FIGURE2
FIGURE3
WIRING DIAGRAM
SCREWLESS
WIRING CONNECTOR
ON CHIME BASE
REAR DOOR PUSHBUTTON
120 VAC
WIRING
TRANSFORMER
FRONT DOOR
PUSHBUTTON WITH
DIODE INSTALLED
A
B
C
FIGURE1
NEW WIRED CHIME INSTALLATION
WARNING
•
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
•
Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
•
Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
•
Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, including
fire-rated construction codes and standards.
•
When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
•
UseNuTone
®
16 volt transformer with a minimum rating of 10 VA (purchase
separately).
•
When stapling wires to studs or joists, do not allow staples to cut through
wire insulation.
1. Mount the transformer to a junction box (attic location is not
recommended) or circuit breaker box.
2. Connecthousepowerleadstotransformerleads:blacktoblack,
white to white, ground to green. (Figure 2)
3. Route 2-conductor 18-22 gauge wire from the transformer screw
terminals and from the pushbutton terminals to the chime location. (Figure
3)
4. Labelallwiresatchimelocationinthefollowingmanner:
“F”–FrontPushbuttonWire
“T”–TransformerWire
“R”–RearPushbuttonWire(ifinstalled)

NuTone la600wh Specifications

General

Color	White
Voltage	16V AC
Power Supply	Transformer
Weight	1.5 lbs
Type	Door Chime

Summary

Installation and Operating Instructions

Upload MP3 Tunes

Instructions for uploading custom MP3 sound files to the doorbell mechanism via USB.

New Wired Chime Installation

General Safety Warnings

Critical safety precautions to reduce fire, electric shock, or injury risks during installation.

Transformer and Wiring Setup

Mounting the transformer, connecting house power, and routing chime wires.

Wire Labeling and Connection

Instructions on labeling wires and connecting them to the chime base.

Wired Pushbutton Installation

Front Door Pushbutton Diode Installation

Essential step to add a diode to the front door pushbutton for continuous power supply.

Pushbutton Wiring and Testing

Connecting pushbutton wires, restoring power, testing operation, and troubleshooting.

Existing Wired Chime Installation

Preparation and Wire Identification

Turning off power, verifying transformer, and labeling wires for existing chime removal.

Re-installation Procedure

Following steps from new installation for re-installing the chime.

Wireless Chime Installation

Battery Installation and Pushbutton Setup

Inserting batteries into the chime mechanism and installing the wireless pushbutton.

Code Setting and Door Assignment

Matching code settings and assigning pushbuttons to specific doors (Front/Rear).

Chime Placement and Troubleshooting

Mounting the chime, confirming operation, and addressing range or connection issues.

Manage Chime Notification

Select a Tune

Instructions for cycling through and selecting desired tunes for front and rear pushbuttons.

Set Tune Duration

Adjusting the playback time for selected tunes using the CUT button.

Adjust Volume

How to cycle through and select desired volume levels for the chime.

Warranty Information

One Year Limited Warranty

Details on NuTone's limited warranty, coverage, exclusions, and claim procedures.