EasyManua.ls Logo

NuTone QT9093WH

NuTone QT9093WH
20 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MODEL QT9093WH
Page 1
MODEL QT9093WH
DELUXE HEAT-A-VENTLITE
®
READ AND SAVE THESE INSTRUC
TIONS
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE INSTALLING OR US-
ING THIS HEATER.
To reduce the risk of fire, electric shock, or injury to persons,
observe the following:
1. Use this unit only in the manner intended by the manufac-
turer. If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the ser-
vice disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
5. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials,
such as furniture, pillows, bedding, papers, clothes, etc. and
curtains at least 3 feet (0.9 m) from the front of the heater.
6. Extreme caution is necessary when any heater is used by
or near children or invalids and whenever the heater is left
operating and unattended.
7. Do not operate any heater after it malfunctions. Disconnect
power at service panel and have heater inspected by a rep-
utable electrician before reusing.
8. Do not use outdoors.
9. To disconnect heater, turn controls to off, and turn off power
to heater circuit at main disconnect panel (or operate inter-
nal disconnect switch, if provided).
10. Do not insert or allow foreign objects to enter any ventilation
or exhaust opening, as this may cause an electric shock or
fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust
in any manner.
12. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable vapors or
liquids are used or stored.
13. Use this heater only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons.
14. Install heater at least 6 inches from floor or any adjacent
wall.
15. To avoid electrical shock: Do not install unit in a tub or show-
er enclosure or any location where it may come in contact
with water. Never place a switch where it can be reached
from a tub or shower.
16. This product is designed for installation in ceilings up to a
12/12 pitch. Duct connector must point up. DO NOT MOUNT
THIS PRODUCT IN A WALL.
17. Do not connect heater to dimmer switch or speed control.
18. Ducted fans must always be vented to the outdoors.
19. This product must be grounded.
SAVE THESE INSTRUCTIONS
Question and Answer IconNeed help?

Do you have a question about the NuTone QT9093WH and is the answer not in the manual?

NuTone QT9093WH Specifications

General IconGeneral
Model NumberQT9093WH
Product TypeElectric Heater
Voltage120V
Wattage1500W
Amperage12.5A
FinishWhite
Weight6.5 lbs
Mounting TypeWall
Safety FeaturesAutomatic Shut-off

Summary

Important Safety and Usage Instructions

General Safety and Usage Precautions

Covers crucial safety rules for installation, operation, and maintenance to prevent fire, shock, or injury.

Installation Guide

Installation Safety Warnings

Important safety precautions regarding fire risks, high temperatures, and combustible materials during installation.

Mounting in New Construction

Step-by-step guide for mounting the heater housing between joists in new construction.

Electrical Wiring Instructions

Detailed steps for connecting the heater wiring, including circuit requirements and connection points.

Completing Installation Steps

Final steps to complete installation, including reattaching unit, plugging components, and installing lamps.

Installation in Existing Construction

Instructions for installing heater in existing structures, detailing hole prep, mounting, and duct connection.

Product Operation

Maintenance Procedures

Bulb Replacement and Lubrication

Instructions for replacing the heater bulb and information on the heater's permanent lubrication.

Cleaning Procedure

Step-by-step guide for cleaning the heater, including safety precautions and recommended tools.

Service Parts and Diagram

One Year Limited Warranty

Related product manuals