Nutricia flocare Infinity III User Manual (English)

Other manuals for Nutricia flocare Infinity III

Questions and Answers:

M
Melissa VelasquezAug 20, 2025
Why Nutricia Water Pump says 'Occlusion out'?
- K
  Karl SmithAug 20, 2025
  The 'Occlusion out' message on your Nutricia Water Pump typically indicates that the sensor area is dirty. Here's what you should do: * Check the Flocare Infinity giving set between the pump and feeding tube for any kinks or obstructions, and correct them if found. * Inspect the feeding tube itself for kinks or obstructions, following your training, and correct them. * Clean the sensor area. If the alarm persists after these steps, replace the Flocare Infinity giving set.
G
gbrooksAug 21, 2025
How to unlock keypad on Nutricia Water Pump?
- M
  Miguel SloanAug 22, 2025
  The keypad on the Nutricia Water Pump is locked to prevent unintended button presses. To unlock it, press the i-Button [ ] and SOFT BUTTON 3 simultaneously.
E
Emily TranAug 25, 2025
Why Nutricia Water Pump says 'Occlusion in'?
- S
  Sydney RoweAug 25, 2025
  The 'Occlusion in' message on your Nutricia Water Pump means that the sensor area is dirty. To resolve this: * Check the Flocare Infinity giving set between the pump and the reservoir for kinks or other obstructions, and correct them. * Restart the pump. * Clean the sensor area. If the alarm continues, replace the Flocare Infinity giving set.
M
Mark LinAug 26, 2025
What to do if Nutricia Water Pump shows 'Set > 24 hrs'?
- J
  John RobertsAug 26, 2025
  The 'Set > 24 hrs' message on the Nutricia Water Pump is a reminder that the giving set has been used for more than 24 hours and needs to be replaced. Replace the Flocare Infinity giving set with a new one.
C
Chelsea WrightAug 28, 2025
What to do if Nutricia Water Pump displays 'Replace giving set'?
- T
  Tyler SmithAug 28, 2025
  If the Nutricia Water Pump displays 'Replace giving set', it means the giving set has been used for more than 24 hours. Replace the Flocare Infinity giving set with a new one.
R
ricesherylAug 29, 2025
What to do if Nutricia Water Pump displays 'Re-insert giving set'?
- J
  jonathanleeAug 30, 2025
  If the Nutricia Water Pump displays 'Re-insert giving set', it indicates that the giving set is not properly installed. Insert a Flocare Infinity giving set.
V
vargaspeterSep 1, 2025
What to do if Nutricia Water Pump shows 'Air in giving set'?
- M
  Michelle DavisSep 1, 2025
  If your Nutricia Water Pump shows 'Air in giving set', it may be because the air sensor area is dirty. If your feeding reservoir is intended to be empty, disconnect and discard the feeding reservoir and Flocare Infinity giving set, or replace them as per your training. If your feed reservoir is NOT intended to be empty, disconnect it from the feeding tube and use the FILL SET function to clear the air. Reattach the feeding tube and restart feeding. Also, ensure there is no excessive foam in the feeding reservoir and that the air sensor is clean.
A
Anthony OconnorSep 3, 2025
What to do if Nutricia Water Pump shows 'System failure'?
- J
  Jacob FisherSep 3, 2025
  If the Nutricia Water Pump displays 'System failure', turn the pump OFF, ensure the pump door is closed, and then switch the pump back ON. If the error persists, contact your pump provider for a replacement.
K
Kristine TownsendSep 5, 2025
Why Nutricia Water Pump is not charging?
- R
  Russell DuncanSep 5, 2025
  If the plug symbol is not visible while your Nutricia Water Pump is connected to the mains, it could be due to a non-functional mains outlet or a damaged AC power adapter. Try connecting the pump to another mains outlet. If the issue persists, contact your pump provider for a replacement adapter.
M
Mario DelgadoSep 7, 2025
What to do if Nutricia Water Pump displays 'Last feeding incomplete'?
- J
  James PerrySep 7, 2025
  If the Nutricia Water Pump displays 'Last feeding incomplete,' it means the pump was turned off before the therapy was completed. Press the START/PAUSE button to start the same therapy all over, or press RESUME to continue your active therapy.