NXP Semiconductors UM11490 - Page 25

NXP Semiconductors
UM11490
Feature Configuration Guide for NXP-based Wireless Modules on i.MX 8M Quad EVK
• Accept the Wi-Fi Direct connection request on the peer or on the mobile device
[ 91.756563] wlan: RX P2P Group Owner Negotiation Req Frame, channel=11
[ 91.763402] wlan: TX P2P Group Owner Negotiation Rsp Frame,
channel=11
[ 91.774831] wlan: RX P2P Group Owner Negotiation Confirm Frame,
channel=11
<3>P2P-GO-NEG-SUCCESS role=client freq=2412 ht40=0 peer_dev=ba:c[
91.807376] Can not set data rate in disconnected state
7:4a:41:e3:3f peer_iface=ba:c7:4a:41:e3:3f wps_method=PBC
> [ 91.819478] Can not set data rate in disconnected state
[ 91.867977] wlan: p2p-p2p0-0 START SCAN
[ 91.915383] wlan: SCAN COMPLETED: scanned AP count=0
<3>CTRL-EVENT-SCAN-RESULTS
> [ 92.171472] wlan: p2p-p2p0-0 START SCAN
[ 92.219913] wlan: SCAN COMPLETED: scanned AP count=1
[ 92.437774] p2p-p2p0-0:
[ 92.437781] wlan: HostMlme Auth received from ba:XX:XX:XX:e3:3f
[ 92.466671] wlan: HostMlme p2p-p2p0-0 Connected to bssid
ba:XX:XX:XX:e3:3f successfully
[ 92.475454] p2p-p2p0-0:
[ 92.475460] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 92.556358] p2p-p2p0-0:
[ 92.556365] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 92.683359] p2p-p2p0-0:
[ 92.683364] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 92.757997] p2p-p2p0-0:
[ 92.758004] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 92.770529] p2p-p2p0-0:
[ 92.770532] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 92.783601] p2p-p2p0-0:
[ 92.783608] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
<3>P2P-GROUP-FORMATION-SUCCESS
> [ 92.847516] p2p-p2p0-0:
[ 92.847521] wlan: HostMlme Disconnected: sub_type=10
[ 92.855281] wlan: Received disassociation request on p2p-p2p0-0,
reason: 3
[ 92.862198] wlan: REASON: (Deauth) Sending STA is leaving (or has
left) IBSS or ESS
[ 92.869898] Already disconnected
<3>CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
> [ 92.974484] wlan: p2p-p2p0-0 START SCAN
[ 93.017544] wlan: SCAN COMPLETED: scanned AP count=1
[ 93.257289] p2p-p2p0-0:
[ 93.257296] wlan: HostMlme Auth received from ba:XX:XX:XX:e3:3f
[ 93.280678] wlan: HostMlme p2p-p2p0-0 Connected to bssid
ba:XX:XX:XX:e3:3f successfully
[ 93.360455] p2p-p2p0-0:
[ 93.360459] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 93.372269] p2p-p2p0-0:
[ 93.372275] wlan: Send EAPOL pkt to ba:XX:XX:XX:e3:3f
[ 93.381399] IPv6: ADDRCONF(NETDEV_CHANGE): p2p-p2p0-0: link becomes
ready
<3>P2P-GROUP-STARTED p2p-p2p0-0 client ssid="DIRECT-fi-
Peer_Device" freq=2412 [ 93.389544] woal_cfg80211_set_rekey_data return:
gtk_rekey_offload is DISABLE
psk=cb765fd7d25a10e1c8acaef5e773658663ff03931615bc3ac6d8d0b1548bd673
go_dev_addr=ba:c7:4a:41:e3:3f [PERSISTENT]
• Close the wpa_cli prompt
> quit
UM11490 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2021. All rights reserved.
User manual Rev. 2 — 29 January 2021
25 / 88