Why is my Oasis FreshStart FSTB-A60 Dispenser not dispensing hot water?
If your Oasis Dispenser isn't dispensing hot water or the water isn't hot enough, verify that the brewer is getting power. You may also need to adjust the thermostat, or replace the primary thermostat or heating element.
What to do if the Oasis Dispenser brew cycle will not start?
If the brew cycle on your Oasis Dispenser isn't starting, there are several things you can check: * Ensure the power cord is properly plugged into the IEC receptacle at the back of the brewer and into a working electrical outlet. * Make sure the power switch is in the “on” position. * Verify the water supply line is correctly connected and turned on. * Inspect and, if necessary, replace the fuse on the circuit board. * Reset the safety float. * Look for mineral buildup, clogs, or kinks in the water lines and fittings. * Clean the spray head. * Check the solenoid valve for mineral buildup or blockage, and replace the valve if needed. * Confirm the volume program procedure was completed correctly.
How to stop my Oasis FreshStart FSTB-A60 carafe from overflowing?
To prevent the carafe of your Oasis Dispenser from overflowing: * Ensure the carafe is empty before starting a fresh brew. * Check the supply line pressure, and add a pressure regulator if needed. * Make sure the float arms can move freely without binding. * Inspect water lines and fittings for mineral buildup, clogs, or kinks. * Remove and air dry the filter. * Check the hot tank for mineral buildup. * Reset the pot size.
How to fix weak coffee from my Oasis FreshStart FSTB-A60 Dispenser?
If your Oasis Dispenser is producing weak coffee, you can try the following: Adjust the thermostat to provide hotter water. Also, clean the spray head. Consider modifying the coffee roast, blend, grind, or filter.
What to do if there is dry coffee remaining in the brew basket of my Oasis Dispenser?
If you find dry coffee remaining in the brew basket of your Oasis Dispenser, try these solutions: Clean the spray head. Sift the grounds flat to set the filter. Check for any mineral build-up, clogs, or kinks in the water lines and fittings.
How to stop a dripping hot faucet on my Oasis FreshStart FSTB-A60 Dispenser?
To stop a dripping hot faucet on your Oasis Dispenser, first, try tightening the hot faucet bonnet by a quarter turn. If the dripping continues, you may need to replace the hot faucet.
Why is the flow rate from the hot faucet on my Oasis FreshStart FSTB-A60 Dispenser so slow?
A slow flow rate from the hot faucet on your Oasis Dispenser could be due to mineral build-up at the faucet outlet or obstructions in the silicone tube connecting the hot tank to the faucet. Check for mineral build-up at the faucet outlet and inspect the silicone tube for mineral build-up, obstructions, or kinks.
Inspect the brewer and its components for shipping damage and ensure proper assembly.
Connect the brewer to a cold water line, checking pressure and tubing installation.
Connect the brewer's power cord to a suitable electrical outlet.
Power up the brewer and allow the hot tank to reach optimal temperature.
Enter the brewer into the volume programming mode.
Set the desired brew volume for the brewer.
Steps to brew coffee, including filter and grounds placement.
Instructions on how to stop an ongoing brewing process.
Procedure for dispensing hot water from the safety faucet.
Procedure to adjust the hot tank thermostat for water temperature control.
Instructions for cleaning the spray head to maintain optimal water flow.
Step-by-step guide to remove the hot tank assembly.
Procedures for resetting safety floats and inspecting float arm movement.
Guidance on checking and replacing the circuit board fuse.
How to inspect and replace the dump solenoid valve.
Detailed steps for replacing the primary and anti-boil thermostats.
Instructions for inspecting and replacing the hot faucet due to mineral buildup.
Information about the float cap air filter and its maintenance.
Notes on maintaining the hot tank against mineral buildup.
To Next Page
General