1
ALI-NVR3404P_SQ
180503
Mouse control
A standard 3-button (left / right / scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse:
1. Plug the USB mouse into the either the front panel or back panel USB connector of the NVR.
2. The mouse will be automatically detected. If the mouse is not detected, the mouse may not be compatible with the NVR. Please refer
to the recommended device list from your provider.
Using the mouse
Action Eect
Left click
Single click: Live view: Select channel and show the quick set menu
Menu: Select and enter
Double click: Live view: Switch between single-screen and multi-screen
Click and drag: PTZ control: pan, tilt and zoom
Tamper-proof, privacy mask and motion detection: Select target area
Digital zoom-in: Drag and select target area
Live view: Drag channel / time bar
Right click
Live view: Show menu
Menu: Exit current menu to upper level menu
Scroll wheel
Scroll up: Live view: Previous screen
Menu: Previous item
Scroll down: Live view: Next screen
Menu: Next item.
Step 1. Getting Started: Unpacking the Equipment
What’s in the box
Your system includes:
• NVR
• 6 foot Ethernet cable
• 6 foot HDMI cable
• 48 Vdc power adapter and cable
• HDD SATA and power interface cables for internal hard disk drive
Remove the equipment from its packaging and place it on a at, clean surface. Inspect each item. If any visible damage is present, contact
your supplier for a replacement. Verify that your order is complete.
What you need
Although each security system installation is dierent, most require the following items not included with your system components:
• VGA or HDMI compatible computer monitor
• IP cameras and cables compatible with the NVR
This quick setup guide provides instructions to initially setup and use the ALI-NVR3404P network video recorder (NVR). For information
about using your NVR and its extensive capabilities, refer to the Alibi Embedded Network Video Recorder Firmware User Manual
provided at www.alibisecurity.com/resources.
For more information, refer to these documents - available from your equipment vendor:
• ALIBI Power Tools Installation and User Manual
• ALIBI™ Witness 2.0 v3 Smartphone App for Android (or Apple iOS) Mobile Devices User Guide
Controls and Indicators
Front panel
Status indicators USB port
Item Function / Description
Status Indicators
POWER Indicator is green when the unit is powered on. When the unit is o, the LED is red if power is available.
HDD HDD indicator blinks red when data is being read from or written to an HDD.
TX/RX Blinks green when the network connection is functioning normally.
USB Interfaces Universal Serial Bus (USB) 2.0 port for additional USB devices such as a mouse or Hard Disk Drive (HDD).
Backpanel
Audio IN/OUT
Internal Ethernet switch
ports with PoE (4)
LAN
Power Adapter
connector
Power switch
Video Out
(VGA, HDMI)
Ground
terminal
USB
Item Description
VIDEO OUT (VGA, HDMI)
1 channel (HDMI/VGA), resolution: 1920 × 1080P / 60 Hz, 1600 × 1200 / 60 Hz, 1280 × 1024 / 60 Hz, 1280 × 720 / 60 Hz,
1024 × 768 / 60 Hz. HDMI also supports 4K video output resolution.
Audio IN / OUT RCA connectors for audio line input and line output
Power connector
Connect the 48 Vdc power adapter provided with the recorder to this port, and to a standard 100 ~ 240 Vac power source using the
power cord provided.
ON / OFF Switch Switch for powering the recorder on or o.
GROUND Terminal for ground. Connect to earth ground before powering on the NVR.
LAN 10/100/1000BASE-T Ethernet network interface
USB interface Universal Serial Bus (USB 2.0) port for additional devices such as USB mouse and USB Hard Disk Drive (HDD).
Internal Ethernet switch ports 4 10/100 Mbps ports for IP cameras. These ports provide Power over Ethernet (PoE).
ALI-NVR3404P Embedded Network Video Recorders Quick Setup Guide
To Next Page
Need help?
General