The Ofuzzi Cyber is a cordless robotic pool cleaner designed for residential flat-bottom pools. It is a rechargeable, automatic cleaning device with an upgraded cleaning function that includes a half-way turn-back feature, activated 5-12 times for every 20 wall hits, to ensure comprehensive cleaning of the pool's center.

Function Description:

The Cyber cleaner operates autonomously, moving across the pool floor to collect dirt and debris. It features two adjustable nozzles that control its movement path. One nozzle opens while the other closes, allowing water to flow out and propel the cleaner forward. By turning the nozzle, users can adjust the cleaner's route to achieve optimal coverage. The device is equipped with an indicator light that signals its status: solid blue for power-on, fast flashing blue for out of water, slow flashing blue for working in the pool, and fast flashing red for low battery. When the battery is low, the cleaner will automatically move closer to the pool wall before stopping.

Important Technical Specifications:

Model: Cyber
Charger Input: 100Vac-240Vac, 50/60Hz
Charger Output Voltage: 12.6V
Charger Output Current: 1.8A
Working Power: Approx. 50W
Working Time: Max. 120 minutes per cycle
Battery Capacity: 6600mAh
Charging Time: 5-6 hours
Max. Cleaning Surface: Approx. 1076 sq ft (100 sq m)
Filter Capacity: Approx. 2641 US gallons (10 cubic m/h)
Filter Capability: 180μm
Swimming Pool Slope: Max. 15°
Pool Water Temperature: 50°F - 95°F (10°C - 35°C)
Moving Speed: Approx. 52.4 ft (16 m/min)
IP Grade: IPX8 (main body)
Charging Environment Temperature: 32°F - 113°F (0°C - 45°C)
Max. Water Depth: 6.56 ft (2.0 m)
Storage Conditions:
- Short term (less than 1 month): -4°F - +140°F (-20°C - +60°C) ≤ 75%RH
- Medium term (less than 3 months): -4°F - +113°F (-20°C - +45°C) ≤ 75%RH
- Long term (more than 3 months): -4°F - +68°F (-20°C - +20°C) ≤ 75%RH

Usage Features:

The Ofuzzi Cyber is ideal for residential flat-bottom pools, including above-ground, half-above-ground, and inground pools with a water depth of less than 6.6 ft. It is not designed for deep shallow ends, climbing walls, or stairs, and is only suitable for flat-bottom pools with slopes no more than 15 degrees. Before use, the brush must be installed, and the top cover should be tightly assembled to the chassis to prevent dirt leaks. After turning on the cleaner, it must be placed in the pool within 20 seconds. When placing it in or lifting it out of the pool, the cleaner's bottom should face the wall to avoid scratches. It is recommended to allow the cleaner to stay on the water surface for 10-15 seconds until water flows out before placing it on the ground. The nozzle angle can be adjusted to control the cleaning path. Default settings (0°-20°) are suitable for most pools, while a wider range (0°-40°) can be used if the default does not provide full coverage. For round pools, a 20°-20° setting is recommended.

Maintenance Features:

Regular maintenance includes cleaning the filter tray after each use. To do this, the cleaner is opened by its clips, the filter tray is removed, cleaned, and then reassembled. The chassis should also be cleaned. When charging, the switch knob must be turned to OFF, and the charging port should be clean and dry. The cleaner should be charged under permitted conditions, in a cool and ventilated place, away from direct sunlight, and not covered to prevent overheating. For long-term storage, the cleaner should be charged every three months to maintain the battery power at 40%-60% using the original and authorized adapter. This prevents over-discharge and fatal damage to the battery. The cleaner should not be powered on when out of water. It is important to power off the cleaner when maintaining, cleaning, or not using it. Only professionals should disassemble the sealed driving kit.

Ofuzzi Cyber - Table of Contents

Table of Contents