olympia electronics BS-489 User Manual

921489000_09_005
Page. 1 from 4
BS-489
Auto Dialer
TECHNICAL SPECIFICATION
Thank you for purchasing this product of
O l y m p i a E l e c t r o n i c s . A E u r o p e a n
manufacturer.
GENERAL
Auto dialer BS-489 is a device that
transmits the stored messages over the
phone line when it is properly triggered.
On the front panel there is a user-
frienly control panel with 4 keys and a
display.
It is combined with all alarm panels
(e g BS - 4 17, BS- 4 18) and wit h fi r e
alarm panels (eg BS-632,BS-634,BS-
63 6 , BS- 116) ma d e by Ol ymp i a
Electronics. It is also compatible with
similar products on the market. It can
be used with two different panels at the
same time, and transmits two different
messages, one for each panel. It has a
me m o ry for te n ph o ne numb e r s of
twenty digits each and it is locked with
a four digit access code.
The device has a built-in microphone
fo r re c o rdi n g m e ssa g es, and a n
earphone is included in the package,
for listening the messages.
All phone numbers , settings , and
messages are recorded in the memory
and are not lost in case of a power
failure, and can be changed by the user
when needed.
It is used to immediat ely call the
police, the fire department, the owners
etc, in case of emergency
When triggered, the auto-dialer dials
th e phon e nu m b ers s tor e d i n its
memory, in priority (0-9) as stored by
the user. The device skips the blank
memory positions.
MOUNTING
The bottom cover can be removed by
unscrewing the retaining screw at the
bottom side of the device. For wall
mounting the mounting holes on the
two corners of the device (shown on
figure 1) can be used. The appropriate
mounting screws for wall mounting, are
included.
CONNECTIONS
At the bottom right side of the
device there are the terminal blocks
Operating Voltage
Degrees of cover protection
User interface
Consumption
Inputs
Outputs
Produced in accordance with
Operation temperature range
Humidity
Constructional materials
Dimensions ( L x W x H )
Weight
Guarantee
10 - 30 V DC
Idle 10mA (24V) or 25mA (12V). Active 25mA (24V) or 70mA (12V)
2 alarm inputs and 2 messages, built-in microphone and earphone
160 gr.
105 x 65 x 28 mm
Polycarbonate
Up to 95% Relative Humidity
ï
0 to 60 C
TBR-21, EN61000-3-2, EN 61000-3-3
IP 20
1 Display and 4 programming keys
tone or pulse call and transmission of messages through phone line
2 years
High Quality European based Manufacturers

olympia electronics BS-489 Specifications

General

Model	BS-489
Manufacturer	Olympia Electronics
Sound Output	105 dB
Operating Temperature	-10°C to +55°C
Humidity	Up to 95% RH

Summary

BS-489 Auto Dialer Product Information

Technical Specifications

Key technical parameters including voltage, consumption, inputs, outputs, user interface, and environmental ratings.

General Description and Compatibility

Overview of the BS-489 Auto Dialer, its function, and compatibility with alarm panels.

Mounting Instructions

Details on how to remove the bottom cover for wall mounting using provided holes.

Connection Terminals Overview

Describes terminal blocks located on the bottom right for power and signal connections.

Device Operation and Programming

Entering the Access Code

Step-by-step guide on how to enter the 4-digit access code using the ESC and ENT keys.

Entering Phone Numbers

Guide to saving up to 10 phone numbers, each up to 20 digits, with priority settings.

Displaying Saved Phone Numbers

How to check saved phone numbers by their priority, displaying digits one by one.

Dialling Check Procedure

Procedure to test normal connection by dialling stored numbers and transmitting recorded messages.

Recording and Listening to Messages

Instructions for recording up to two different messages and listening to them using the earphone.

Tone or Pulse Dialling Selection

How to select between tone or pulse dialling methods, with default set to tone.

Alarm Operation Settings

Configuring how the device operates when triggered by alarm inputs A or B.

Re-Dial Setting Configuration

Setting how many times each stored number will be dialled.

Message Re-play Setting

Setting how many times a message will be played during each call.

Setting the Access Code

Changing the 4-digit access code from the factory default.

Exiting the Main Menu

How to exit the programming menu and return the device to idle mode.

Resetting the Access Code

Procedure to reset the access code back to the factory default using a jumper.