Omega OTEC IEWQ Series - Page 15

14
Technical Information
● When selecting auto mode, air conditioner will operate automatically according to the sensed temperature.
.deeps naf tsujda nac nottub "NA " sserP .llew sa deyalpsid eb ton lliw dna detsujda eb t’nac erutarepmet teS F
Press " " / " "
button can adjust fan blowing angle.
● After selecting cool mode, air conditioner will operate under cool mode. Cool indicator " " on indoor unit is ON.
(This
indicator is not available for some models)
nottub " " / " " sserP .deeps naf tsujda
ot nottub "NAF" sserP .erutar -epmet tes tsujda ot nottub " " ro "▲" sserP.
.elgna gniwolb naf tsujda ot
● When selecting dry mode, the air conditioner operates at low speed under dry mode. Dry indicator " " on indoor unit
.elgna gniwolb naf tsujda ot nottub " " / " " sserP .detsujda eb t’nac deeps naf ,edom yrd rednU
(This indicator is not available for some models).NO si
● When selecting fan mode, the air conditioner will only blow fan, no cooling and no heating. All indicators are OFF,
.elgna gniwolb naf tsujda ot nottub " " / " "sserP .deeps naf tsujda ot nottub "NAF" sserP
.
(This indicator is not available for some models)NO si rotacidni noitarepO
● When selecting heating mode, the air conditioner operates under heat mode. Heat indicator " " on indoor unit is
"FAN" button sserP .erutarepmet tes tsujda ot nottub " " ro "▲" sserP
NO
to adjust fan speed. Press " " / " " button to adjust fan blowing angle. (Cooling only unit won’t receive heating mode
signal. If setting heat mode with remote controller
,.
)tinu eht pu trats t’nac nottub FFO/NO sserp
▲
▲
AUTO COOL FANDRYHEAT
Note:
● For preventing cold air, after starting up heating mode, indoor unit will delay 1~5 minutes to blow air (actual delay time
is depend on indoor ambient temperature).
● Set temperature range from remote controller: 16~30
(61-86°F);
Fan speed: auto, low speed, low-medium speed,
medium speed,medium-high speed,high speed.
3.FAN button
This button is used for setting Fan Speed in the sequence that goes from AUTO,
to
then back to Auto.
,
,,
,
Auto
Medium speedLow-Medium speedLow speed
High speedMedium-High speed
Note:
4.TURBO button
Under COOL or HEAT mode, press this button to turn to quick COOL or quick
HEAT mode. " " icon is displayed on
remote controller. Press this button again to exit turbo function and " " icon will disappear.
If start this function, the unit will run at super-high fan speed to cool or heat quickly so that the ambient temp. approachs
the preset temp. as soon as possible.
▲
5.▲/ button
● Press "▲" or " " button once increase or decrease set temperature 1
(°F). Holding "▲" or " " button, 2s later,
-acidni erutarepmet ,dehsinfi si gnittes retfa nottub gnisaeler nO .ylkciuq egnahc lliw rellortnoc etomer no erutarepmet tes
tor on indoor unit will change accordingly
. (Temperature can’t be adjusted under
▲
▲
● It’s Low fan speed under Dry mode.
This function indicates that moisture on evaporator
of indoor unit will be blowed a fter the unit is stopped to avoid mould.
Having set X-FAN function on: A rof gninnur eunitnoc lliw naf roodni nottub FFO/NO gnisserp yb tinu eht ffo gninrut retf
,doirep siht nI .deeps wol ta .setunim wef a
Hold fan speed button for 2s to stop indoor fan directly.
ltcerid ffo eb lliw tinu etelpmoc eht ,nottub FFO/NO gnisserp yb tinu eht ffo gninrut retfA :ffo noitcnuf NAF-X tes gnivaH y.
X-FAN function
Hold fan speed button for 2s in COOL or DRY mode, the icon “ ” is
displayed and the indoor fan will continue
operation for a few minutes in order to dry the indoor unit even though you have turned off the unit. After energization, X-FA
N
OFF is defaulted. X-FAN is not available in AUTO, FAN or HEAT mode.
●
●
●
▲
auto mode)
● When setting TIMER ON, TIMER OFF or CLOCK, press "▲" or " " button to adjust time. (Refer to CLOCK, TIMER ON,
TIMER OFF buttons)
(This indicator is not available for some models).