• No power.
Cause: Power cable is not properly plugged into the AC outlet.
Remedy: Insert the power plug firmly.
• A disc is loaded in the disc tray, but playback will not start.
Cause: A disc in the disc tray may be upside down.
Remedy: Load the disc with the label facing upward.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: Moisture has accumulated inside the CD changer.
Remedy: Remove the disc from the disc tray, place the CD
changer in a warm place, and leave the power on for
about one hour.
• No sound is heard.
Cause: Connections may be incomplete or incorrect.
Remedy: Check all cable connections. Insert all the plugs firmly
into the jacks.
Cause: The input selector switch on the amplifier may be set in-
correctly.
Remedy: Set the switch to the proper position. See your amplifier’s
operating instructions for more information.
• Disc playback skips.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: A disc is scratched.
Remedy: Replace the disc.
Cause: The CD changer is subject to being accidentally bumped.
Remedy: Place the CD changer in a more stable location.
• Search time (when locating a specific track) is extremely long.
Cause: The disc is dirty.
Remedy: Clean the disc.
Cause: The disc is scratched.
Remedy: Replace the disc.
• Track numbers cannot be stored in memory.
Cause: No disc in the tray.
Remedy: Load a disc in the tray.
Cause: You have entered a track number that does not exist on the disc.
Remedy: Use only the track numbers that exist on the disc.
• Front panel controls function correctly, but remote control-
ler does not.
Cause: No batteries in remote controller.
Remedy: Insert batteries.
Cause: Batteries have worn out.
Remedy: Replace batteries.
Because the unit contains a microcomputer to provide advanced functions, it may
malfunction due to external noise or static electricity. If this happens, press the POWER
switch on the unit and then press it in again after about five seconds.
Troubleshooting Guide
Specifications
Signal readout system: Optical non-contact
Reading rotation: About 500 - 200 r.p.m.
(constant linear velocity)
Linear velocity: 1.2 - 1.4 m/s
Error correction system: Cross Interleave Reed-Solomon code
D/A converter: 1 bit PWM/ACCUPULSE
Sampling frequency: 352.8 kHz (8 times oversampling)
Number of channels: 2 (stereo)
Frequency response: 5 Hz - 20 kHz
Total harmonic distortion: 0.005% (at 1 kHz)
Dynamic range: 96 dB
Signal to noise ratio: 92 dB
Channel separation: 92 dB (at 1 kHz)
Wow and Flutter: Below threshold of measurability
Output level: 2 volts r.m.s.
Power consumption: 10 watts
Power supply: 120 V, 60 Hz
230V, 50 Hz
220-230V/120V switchable, 50/60 Hz
Dimensions (W × H × D): 435× 131× 433mm
(17-1/8" × 5-3/16" × 17-1/16")
Weight: 6.9 kg (15.2 lbs.)
Specifications and features are subject to change without notice.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 0720-31-8111 Fax: 0720-33-5222
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramesy, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: onkyo@onkyousa.com
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 20, 82110 Germering, GERMANY
Tel: 089 84 93 20 Fax: 089 84 93 226 E-mail: info@onkyo.de
ONKYO EUROPE FRANCE BRANCH
Domaine Technologique de Saclay 4, Rue René Razel, SACLAY-91892
ORSAY CEDEX, FRANCE Tel: (1) 69 33 14 00 Fax: (1) 69 41 35 84
ONKYO CHINA LIMITED
Units 2102-7, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852 2429 3118 Fax: 852 2428 9039
E
http://www.onkyo.co.jp/
HOMEPAGE
SN 29342705
I9902-1
To Previous Page
Loading...
Need help?
Audio Specifications
Power
Weight and Dimensions
