Onkyo TX-RZ1100-B - Page 50

14
> Specifications > Settings > Listening Modes > Playback Function > Basic Manual
Troubleshooting | Appendix
Setting Item Default Value Setting Details
Front Right 0.0 dB Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Height 1 Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Height 1 Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Height 2 Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Height 2 Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Surround Right 0.0 dB Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Surr Back Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Setting Item Default Value Setting Details
Surr Back Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Surround Left 0.0 dB Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Subwoofer 1 0.0 dB Select a value between "−15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Subwoofer 2 0.0 dB Select a value between "−15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
■ 5� Dolby Enabled Speaker
Setting Item Default Value Setting Details
Dolby Enabled
Speaker to
Ceiling
6' 0" / 1.80 m Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between " 0' 0" 1/2
"/"0.01 m" to " 15' 0" "/"4.50 m" (1/2 / 0.01 m units).
•
The unit of distance (feet / meters) shown is the
unit selected for use in "Distance".
AccuReflex Off You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": Do not use this function
"On": Use this function
•
This setting can be selected when "Configuration" - "Height 1 Speaker"/"Height 2 Speaker" is set to
"Dolby Speaker".
■ 6� Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust