Onwa LD-510 - User Manual

Questions and Answers

D
Destiny MedinaAug 17, 2025
Why my Onwa LD-510 Washer does not start?
- A
  Autumn SmithAug 17, 2025
  If your Onwa Washer doesn't start, there are several potential causes. First, ensure the machine is properly plugged into a functioning power outlet. Check the fuses and replace them if they are faulty. Verify that there is mains power supply. Make sure you have pressed the Start/Pause button and that the programme dial is not in the ‘stop’ position. Finally, ensure the machine door is completely closed.
K
Katherine HernandezAug 20, 2025
How to fix Onwa LD-510 that does not intake water?
- D
  Daisy RamirezAug 20, 2025
  If your Onwa Washer isn't taking in water, start by checking if the water tap is turned on. Inspect the water inlet hose to ensure it isn't twisted, and untwist it if necessary. Also, the water inlet hose or the inlet filters might be clogged, so clean them. Lastly, make sure that the machine door is completely closed.
C
costashaneAug 22, 2025
Why is my Onwa LD-510 vibrating so much?
- P
  Patty BeardAug 22, 2025
  If your Onwa Washer is vibrating, it could be due to several reasons. First, make sure the feet of the machine have been adjusted properly. Check if the transit bolts, which are fitted for transportation, have been removed. Avoid overloading the machine with laundry, and ensure the laundry is spread evenly inside the drum. Also, avoid setting up your washing machine on a hard surface.
U
upriceAug 25, 2025
What to do if my Onwa LD-510 Washer does not discharge water?
- H
  harveynicoleAug 26, 2025
  If your Onwa Washer isn't discharging water, the drain hose might be clogged or twisted; inspect it and clean or untwist it as needed. The pump filter could also be clogged, so try cleaning it. Lastly, if the laundry is too tightly packed, spread it evenly in the drum.
S
Sharon MoranAug 28, 2025
How to improve unsatisfactory washing result in Onwa LD-510?
- J
  Jacqueline NavarroAug 28, 2025
  An unsatisfactory washing result from your Onwa Washer could stem from a few issues. If the washing is too dirty for the selected programme, choose a more appropriate programme using the information in the programme tables. Ensure you are using a sufficient amount of detergent as instructed on the packaging. Also, check that you have not exceeded the maximum laundry capacity for the selected programme.
J
Julie ReyesAug 30, 2025
How to stop excessive foam in Onwa LD-510 Washer detergent drawer?
- C
  cameronhardinAug 30, 2025
  If excessive foam is forming in the detergent drawer of your Onwa Washer, it's likely due to using too much detergent or using the wrong type. To stop the foam, press the Start/Pause button, dilute one tablespoon of softener into 1/2 litre of water, and pour the mixture into the detergent drawer. Press the Start/Pause button again after 5-10 minutes. Ensure that you only use detergents specifically produced for automatic Washing Machines.
T
Tracy JimenezSep 2, 2025
Why spin cycle does not take place in Onwa Washer?
- R
  Robyn KnightSep 2, 2025
  If the spin cycle in your Onwa Washer doesn't start or is delayed, it may not be a fault. The Unbalanced load control system might have been activated. This system attempts to spread your laundry evenly, and the spin cycle will begin once the laundry is properly distributed. For the next wash, ensure you load the drum evenly.
T
tracyconwaySep 5, 2025
What causes unsatisfactory washing result with Onwa LD-510?
- K
  Karen PearsonSep 5, 2025
  If you're getting unsatisfactory washing results with your Onwa Washer, especially in areas with hard water, try increasing the amount of detergent according to the manufacturer’s instructions. Also, ensure your laundry is spread out in the drum and not too tightly packed.
B
Brett GriffithSep 7, 2025
How to remove detergent residue from Onwa LD-510 laundry?
- J
  John ReidSep 8, 2025
  If your laundry has detergent residue after washing in your Onwa Washer, it's possible that non-dissolving particles from some detergents are appearing as white spots. To resolve this, perform an extra rinse cycle or clean your laundry with a brush after it dries.
K
Kathleen WallerSep 12, 2025
Why Onwa LD-510 Washer discharges water immediately after loading?
- S
  smooreSep 12, 2025
  If water discharges from your Onwa Washer as soon as it's loaded, the end of the water drain hose may be too low. Check that the drain hose is positioned at a suitable height.