DO NOT DISCARD – GIVE TO USER
WARNING
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
BEFORE USE
Study, understand and follow all instructions
provided with this product. Read these instructions
carefully before installing, operating, servicing or
repairing this tool. Keep these instructions in a safe
accessible place.
INTENDED USE OF THE TOOL
Model: Product Type:
PRODUCT INFORMATION:
This pneumatic tool is designed to set aluminum,
steel and stainless rivet nuts in the sizes M10,
M12, 3/8" and 1/2". Do not use this tool outside of
the designed intent. Never modify the tool for any
other purpose or use.
WARNING
Caution: To help prevent personal injury.
• Normal use of this product is likely to expose the
user to dust and/or microscopic particles containing
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Always
wear appropriate safety equipment and clothing when
using this product. Study, understand and follow all
instructions provided with this product. Failure to read
and follow all warnings and operating instructions may
result in damages and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct
size and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is
in secure position and will not move during repair.
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original
user against defective material or workmanship for a period of
1 year (except where noted on our price schedule) from the
date of 1st use. Astro reserves the right to determine whether
the product failed because of defective material, workmanship
or other causes and to charge back for missing parts.
Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor
should direct the original user to return the product (with the
exceptions listed below) with the distributor’s name, address,
adequate proof of date of purchase or a copy of warranty card,
and a short note explaining the problem.
Failures caused by accident, alteration, or misuse are not
covered by this warranty.
• Astro Pneumatic Tool Co. or its authorized service
representatives must perform all warranty repairs. Any repair
to the product by unauthorized service representatives voids
this warranty. The rights under this warranty are limited to the
original user and may not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or
implied, including warranties of merchantability and fitness for
a particular purpose. Some states do not allow the exclusion
of limitations of incidental or consequential damages so the
above limitations may not apply to you.
Before use, check the parts diagram and part
number listing on page 4-6 to make sure all parts
are included. If any parts are missing or damaged,
please call your distributor.
Page 1
ONYX PNEUMATIC
RIVET NUT SETTING GUN
• Two different mandrel sizes provided with each tool
• 400 RPM
• 1/2" (12mm) capacity
• Forward and reverse actions for quick operation
• Adjustable power, dial in regulator setting for
specific rivet nut sizes and compositions
SPECIFICATIONS:
PRN12 PRN12M
Free Speed:
Capacity:
Air Inlet:
Optimal pressure:
Net Weight:
400 RPM
1/2" 12 mm
1/4" (6mm)
Adjust at regulator based on rivet
nut size and material composition
3.489 lbs. (1.58 kgs)
PRN12 - SAE 3/8" & 1/2"
PRN12M - Metric M10 & M12
To Next Page
Need help?
General