6A- 28 1973 OPEL SERVICE MANUAL
Part
Connecting
Rod Bolts
..........................................................
Crankshaft Main Bearing Bolts
..........................................
Flywheel
to
Crankshaft Attaching
Bolts ..........................
Cylinder Head Attaching Bolts
....
Cold 72 -Warm 58
Camshaft Sprocket Attaching Bolts
................................
Generator Bracket to Cylinder Block
Attaching Bolts ..................................................................
Generator Bracket to Timing Case Attaching Bolts
....
Crankshaft Pulley Attaching Bolts ....................................
Rocker Arm Stud in Cylinder Head ..................................
Spark Plugs
............................................................................
Clutch Housing to Cylinder Block Attaching Bolts
......
Timing Case to Cylinder Block Attaching
Bolts
............
Water Pump to Timing Case Attaching
Bolts
................
Engine Support to Cylinder Block Attaching Bolts
......
Rear Engine Suspension to Transmission Rear
Bearing Retainer Bolts ....................................................
Transmission to Clutch Housing Attaching Bolts
........
Starter to Clutch Housing Attaching
Bolts ....................
Support to Starter Attaching Nut
....................................
Intake and Exhaust Manifold to Cylinder Head
Attaching Bolts
..................................................................
Unless Otherwise Noted:
10
@i
Bolt (15 MM
Hall
............................................................
.......
..-
-
36
72
43
18
;i
72
29
30
36
14
11
40
22
29
40
4
33
............
30
8
MM Bolt (13 MM Head)
...............................................................................................................................................................................
.....
....
15
6 MM Bolt (10 MM Head)
30
Lb.In.
Torque
Lb.Ft.
GENERAL SPECIFICATIONS
Type
-
No. of Cylinders
Valve Arrangement
......................................................................................................................................................................................................
I;nlinzai
Bore and Stroke
Piston Displacement Cu. In.
........
3.66
x1:;:;
Compression Ratio
..............
................................................................................................................................................................................................................................................................ô²…
..............
7.6:1
Octane Requirement
..................................................................................
Firing Order
................................................................................................
Regular
-
Lo;-?::
...............
..
...
Cylinder Block Material
....... .......
............................................................................................
....
...................
...
Cast Iron
Crankshaft Bearings Number and Type
5 Removable Steel Backed
In-Metal Babbitts
Bearing Which Takes End Thrust
...........................................................................................
5
Connecting Rod Bearing Material
..........................................................................................
Steel Backed Tri-Metal Babbttts
Piston Material and Surface
Aluminum Alloy, Lead Coated
Piston Pin Offset
....................................................................................
,031
In. to the Right
Compression Rings Material and Surface Treatment
No.
1
....... ........... ............... ........ .............
................
Chrome-plated, Cast Iron
-
Rectangular
No. 2
......................................................................................................
Cast Iron
-
Tapered
Oil Ring
..........................................................................................
Chrome-plated, Cast Ir?n
Location of All Piston Rings
........................................................................
Above Ptston Pm
Camshaft Material
............................................................................................
Alloy Cast Iron
Camshaft Drive
................................................................................................................
Chajn
Number and Type of Camshaft Bearings 4 Steel-Backed
Babbttt
Valve Lifter Type
.
....
.................
...........................................................................................................
...
..
..~
..........
Hydraulic
Oiling System
Tvoe
........................................................................
Circulatmg High Pressure
Oil &ppiied to:
-
.
Bearing Surfaces, Crankshaft, Camshaft and Connecting Rods
............................
Pressure
Piston, Pins
....................................................................................................................
Vapor
Cvlinder Walls
..................................................................................................
Nozzle Spray
Rocker Arms
_,,,..,,....,._..___.,,..,,..............,,,,...,.......,..,,,.,.,,.........,,...,.,.................~......
Pressure
Oil Reservoir Capacity
-
Quarts
.,,,...,,__.,,..,..,,..,...,..,,,...,,..............,,,...
3
l/4
With Dry Fdter
Oil Filter
-
Type
,,....,__.,,...,....,....,,..,,,..,,...........,....................................
Throw Away Element
To Next Page
Loading...
