EasyManua.ls Logo

orangemarine VHF WP 250 - User Manual

orangemarine VHF WP 250
110 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Manuel d'utilisation
VHF Marine Transceiver
Fonction d’Appel Sélectif Numérique (ASN)
Fonction d’évacuation de l’humidité par vibrations
Étanchéité IPX7
Récepteur GPS intégré
VHF WP 250
Transmetteur Marin

Table of Contents

Questions and Answers

  • L
    Leah GarciaAug 8, 2025
    How to fix orangemarine Transceiver that does not turn on?
    • B
      Bob HartAug 8, 2025
      If your orangemarine Transceiver isn't turning on, here's what to check: 1. **Power Cable:** Ensure the power cable is correctly connected, paying attention to polarity: red (+) and black (-). 2. **Fuse:** If the fuse is broken, identify the cause, and replace it with a new 15A fuse. 3. **Voltage:** Verify the operating voltage is within the range of 9V to 17V. Adjust the power supply to 13.8V if necessary.
  • K
    Kristopher SmithAug 12, 2025
    What to do if orangemarine Transceiver is unable to connect with GPS?
    • B
      Bridget HudsonAug 12, 2025
      If you're unable to connect your orangemarine Transceiver with GPS, check the following: * **Connection:** Make sure the GPS connection is correct. * **GPS Format:** Ensure your external GPS format is NMEA 0183-2.0 or 3.01.
  • K
    kimberlynelsonAug 16, 2025
    Why distress call cannot be transmitted on orangemarine Transceiver?
    • B
      Brianna LloydAug 16, 2025
      If a distress call cannot be transmitted from your orangemarine Transceiver, it might be because the MMSI (DSC self ID) code is not programmed. To program it, power on the device while pressing and holding the [MENU] button to enter MMSI set mode.
  • S
    Stephanie OconnorAug 20, 2025
    What to do if orangemarine VHF WP 250 Transceiver is unable to transmit?
    • D
      Dr. Patrick AguirreAug 20, 2025
      If your orangemarine Transceiver is unable to transmit, it might be because you are on the Weather Channel, Channel 70, or an RX Only Channel. Exit these channels and select other channels to transmit.
  • J
    Jack BatesAug 26, 2025
    Why can’t I communicate on same channel on orangemarine VHF WP 250 Transceiver?
    • D
      Dr. Randy MorenoAug 26, 2025
      If you can't communicate on the same channel using your orangemarine Transceiver: 1. **Duplex Channel:** The channel may be set to duplex (DUP). Select a different channel. 2. **Self-Set Channel Group:** If working in a self-set channel group, ensure the channel frequency is set to the same frequency on all devices.
  • J
    Jason WilsonAug 29, 2025
    How to fix unable to scan on orangemarine VHF WP 250?
    • J
      John CervantesAug 29, 2025
      If your orangemarine Transceiver is unable to scan, it could be because no TAG channel is set. Set the channels you want to scan as TAG channels.
  • B
    Bryan VillanuevaSep 2, 2025
    Why can't I select high power on orangemarine Transceiver?
    • C
      Carol ButlerSep 2, 2025
      If you can't select high power on your orangemarine Transceiver, it's because some channels can only be transmitted at low power. Try selecting other channels.

orangemarine VHF WP 250 Specifications

General IconGeneral
Brandorangemarine
ModelVHF WP 250
CategoryTransceiver
LanguageEnglish