ELEC TRONICAL LY CONTROLLE D
SING LE POI NT LOCK OR LATCH
U
L
MOTOR
CONNECTOR
RESET
BUTTON
TERMINAL BLOCK
(FOR REMOTE SWITCH)
CPU PC
BOARD
ASSEMBLY
RED
WIRE
BLACK
WIRE
1580 JAYKEN WAY
CHULA VISTA, CALIFORNIA. 91911
(619) 628-1000 FAX (619) 628-1001
SECURITY
Copyright 2001 OSI Security Devices Inc. All Rights Reserved
OMNILOCK is a Registered Trademark of OSI Security Devices Inc. FALCON is a trademark of Falcon Lock Co. 11523 Rev A
SECTION 5: INSTALL THE STRIKE
SECTION 7: REMOTE SWITCH
a. Remote operation of the System may be accomplished by a momentary Switch
closure. This may be desirable for someone monitoring a protected entrance,
such as a receptionist. Momentarily pressing the Switch will cause the System
to go through a normal unlock and lock sequence. If the Switch is held closed,
the open time will be extended.
b. Connect a twisted pair of wires from the Terminal Block on the PC Board to a
normally open momentary contact Switch. Plan the route for your wire and the
access route through the door to the PC Board in the OMNILOCK Module. Plan
for disconnecting the wires in the module area so that the System can be
removed from the door to change the Batteries as required. Refer to Fig.14.
(Website: WWW.OMNILOCK.COM)
OMNILOCK
SWITCH
TWISTED
OMNILOCK
ACCESS CONTROL SYSTEMS
SECURITY
WARNING: THIS PRODUCT IS NOT WARRANTED FOR
OUTDOORS USE!
NOTE: A DOOR-CLOSER IS HIGHLY RECOMMENDED
FOR USE WITH THIS PRODUCT.
THIS PRODUCT IS NORMALLY FACTORY-PACKED
FOR RIGHT-HAND 1-3/4” TO 2” THICK DOORS.
TO CHANGE HAND OF LOCK, SEE
INSTRUCTION SECTION 2.
LOCK
CONNECTOR
(Routes through
the slot in the
Door)
SCREW
POST
OUTER TRIM
ASSEMBLY
INTERCHANGEABLE CORE (I.C.)
I.C. CORE
(NOT SUPPLIED)
CONTROL KEY
(NOT SUPPLIED)
I.C. CYLINDER
WITH CAM
NYLON
WASHER
SCREW
FLAT HEAD
#12 X 1”
(2-REQD)
STRIKE
STRIKE
SCREW
FLAT HEAD
#12 X 1” (2-REQD)
WASHER
INSIDE
LEVER
SCREW, FLAT
HEAD #6X1/2”
(2-REQD)
SCREW
FLAT HEAD
#8X2-1/4”
(2-REQD)
INSTALLER NOTES: Leave these instructions and other Documents with the User.
CYLINDER
WAVY
WASHER
HOUSING
SCREW
PAN HEAD
#6-32X1/4”
STANDOFF
#8-32X1”
(2-REQD)
AA ALKALINE
BATTERY, 1.5V
(4-REQD)
BATTERY
COVER
GASKET
SEMS #4-40X1/4”
PAN HEAD
SCREWS,
FLAT HEAD
#8-32X3/8”
LG (2-REQD)
SPRING
CYLINDER
COLLAR
BACK
PLATE
CONNECTOR
ASSEMBLY
SCREW, PAN HEAD TORX
#8-32X1-1/2” FOR 2” THICK DOOR
#8-32X1-1/4” FOR 1-
LOCK
FACE
PLATE
SCREW, FLAT
HEAD #10-32 X 2”
(2 REQD)
ASSEMBLY
SPINDLE & SPRING
INSTALLATION INSTRUCTIONS FOR OM100, OM300,
NON-WEATHERIZED, MORTISE
LOCKSETS USING FALCON
™
LM SERIES LOCKS (LEVER)
a. Draw a vertical line on the Door Frame 1/2 the Door thickness
from the Door Stop. Refer to Fig.13.
CAUTION: Allow for paint buildup or weather stripping if required.
b. Select the Strike with the proper hand condition and align the
bottom edge of the Strike Lip with the mark on the Door Frame
and align the center of the mounting holes in the Strike with the
vertical line on the frame. Using the Strike as a template, mark the
Door Frame.
c. Using the Strike Box as a template, mark the Door Frame.
d. Mortise the Frame to accept the Strike and Strike Box.
e. Install the Strike Box and the Strike and secure with the Screws.
COLLAR
SET
ALIGNMENT
MARKS
SCREW
#12X1
SECTION 6: PROGRAM THE LOCK
IMPORTANT: To avoid unauthorized access, it is important to program a new Master Code.
For programming instructions refer to the Quick Reference Guide shipped with this product or to the OMNILOCK
User Guide which may be ordered by calling Customer Service at 619-628-1000 or it may be downloaded from out
website http:/omnilock.com/files/om135man.pdf
LEFT
HAND
INSIDE
OUTSIDE
INSIDE
OUTSIDE
REVERSE
BEVEL
REVERSE
BEVEL
To Next Page
Need help?
General
